Advertisement
NOTE: this appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in
a safe way and understand the hazards involved. children shall not play with the appliance. cleaning and user maintenance shall not
be made by children without supervision.
2. INTRODUCTION
A totally dry heat, no condensation, no gas, no fumes and no smell. reaches maximum heat output within seconds of being turned on. Highly
polished aluminium reflector for maximum heat efficiency. Adjusts horizontally through 45° while mounted. Three settings controlled by pull chain,
allow unit to be on full, half or low power. Indicator panel allows easy indentification of settings. Ideal for industrial or domestic applications.
suitable for indoor use only.
3. SPECIFICATION
model no: ............................................................. iWmH2013
Power: .........................................................................1500W
supply: ................................................................. 230V - 13A
dimensions: ............................................455 x 100 x 180mm
mounting bracket stand off: .......................................... 59mm
minimum mounting height: ....................................... 1800mm
4. INSTALLATION
IMPORTANT! this heater is supplied without a plug. if it is to be installed into a bathroom or similar location it should be wired into a
‰
fused isolator switch, otherwise a 13A plug may be fitted. Both these tasks must be completed by a competent electrician.
IMPORTANT! the heater should always have a minimum clearance of 500mm from a ceiling and at least 500mm from any
‰
perpendicular wall and 1m from any object. ensure that mounting surface is capable of supporting the weight of the heater.
Fig.1
4.1.
Drill four holes using the above diagram to refer to their spacings (fig.1).
4.2.
Use fixings suitable for the wall type, ensuring that they are capable of bearing the weight of the heater.
4.3.
Insert four screws into the fixings and hook the heater over the screw heads and allow the heater to drop into the keyhole slots (fig.2).
4.4.
Scribe through securing lug hole (fig.2), remove the heater and drill a fifth hole in the position of the scribed mark and insert a suitable
fixing.
4.5.
replace the heater as in and insert a screw through the securing lug
into the fixing prepared in 4.4.
5. OPERATION
WARNING! ensure you read, understand and apply the safety instructions
‰
in section 1 before using the heater.
5.1.
ensure the heater is at least 1m from any object. the heater can be tilted
from 0° to 45°, set it to the required angle before switching the heater on.
5.2.
Pull cord once, twice or three times to select desired heat setting and a
fourth time time to turn off.
6. MAINTENANCE
6.1.
make sure the heater plug is disconnected or the heater is isolated from the
mains supply before any cleaning is attempted. Also allow the heater to
cool completely. DO NOT use water or other liquids, or harsh abrasive
cleaners to clean the heater. DO NOT touch the carbon fibre elements with
fingers as this may damage the tube.
6.2.
clean the exterior with a soft damp cloth with some mild detergent.
6.3.
to replace any of the elements or lamps, contact your authorised sealey dealer.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
Fig.2
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
Original Language Version
Environmental Protection
Recycle unwanted materials instead of
disposing of them as waste. All tools,
accessories and packaging should be
sorted, taken to a recycling centre and
disposed of in a manner which is compatible
with the environment.
When the product becomes completely
unserviceable and requires disposal, drain
off any fluids (if applicable)
into approved containers and dispose of the
product and the fluids according to local
WEEE Regulations
Dispose of this product at the end of its
working life in compliance with the EU
Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer
required, it must be disposed
of in an environmentally protective way.
Contact your local solid waste authority for
recycling information.
01284 757500
01284 703534
iWmH2013| issue:4 (l) 04/05/17
regulations.
Directive on
www.sealey.co.uk
Web
sales@sealey.co.uk
Advertisement
