TCS Basys Controls QD2010a Product Manual
  1. Manuals
  2. Brands
  3. TCS Basys Controls Manuals
  4. Conference System
  5. QD2010a
  6. Product manual

TCS Basys Controls QD2010a Product Manual

Embedded site communication center
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
Product Manual

Description

The QD2010a Series Embedded Site Communication
Center is designed to act as an Internet gateway
appliance working in conjunction with the centrally
hosted Ubiquity web application. Users can network
the QD2010a utilizing the onboard Ethernet port.
Loop Control and energy metering of demand and
consumption is standard to the unit as well.

Features

•
Integrated Web Server with 512 MB of Flash
memory and 512MB of DDR2 memory
•
Integrated 10/100 Ethernet controller with firewall
capabilities
•
Interface into Ubiquity
•
Interface for configurations
•
Remotely upgradable firmware
•
User definable communication cycles
•
SSL (Secure Socket Layer) enabled web pages
•
Integrated controller addressing
•
Supports up to 3 TCS Basys Controls devices
2800 LAURA LANE • MIDDLETON, WI 53562 • (800) 288-9383 • FAX (608) 836-9044 • www.tcsbasys.com
QD2010a
Embedded Site Communication
Center
Contents
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
Checkout and Troubleshooting. . . . . . . . . . . . . . . . . . 8

Material List

•
QD2010a Site Communication Center
•
Power cord
•
10 ft CAT 5 Crossover Cable (used for connecting
directly from PC to QD2010a only)
•
10 ft CAT 5 Patch Cable
•
QD1010-USB USB to RS485 Converter
R
1
1
1
1
2
. . . . . . . . . . . . . . . . . . .
2
2
3
3
. . . . . . . . . . . . . . . 3
4
6
. . . . . . . . . . . . . . . . . . . . 7

Advertisement

Table of Contents
loading

Summary of Contents for TCS Basys Controls QD2010a

  • Page 1: Table Of Contents

    ....... the QD2010a utilizing the onboard Ethernet port. Prior Connection to Network .

  • Page 2: Programming

    (Internet Explorer 5.0 or higher). direct connection from a laptop or desktop PC using the 1. Power up the QD2010a unit and give it 5 minutes included CAT 5 crossover patch cable (setup mode) to to fully boot up. The QD2010a should not be view the configuration page using a web browser.

  • Page 3: Mounting

    QD2010a. On units without displays, controller addressing is done by direct connect to The QD2010a is designed to be hung on a wall or set QD2010a. (see Control Addressing section). on a table or shelf. When mounting directly to a wall, use the included mounting bracket.

  • Page 4: Setup Page

    Site Time. The Site Time then grounded at one end of the network. Caution is used by the local network and QD2010a until the should be taken to avoid running wire near power wires, Ubiquity central server performs a time synchronization frequency drives, fluorescent lights, ballasts, etc., which...
  • Page 5 Communications Options: In many cases the QD2010a starts out in s etup mode which allows you to access the Setup Page. The QD2010a will need to be set to Ethernet to Central server after fully configuring it to work with the local network and prior to connecting it to the local network.

  • Page 6: Commissioning Tools

    Ubiquity central server BUT is not being matched up Commissioning Tools with a specific Site Home page. This will be the case until one of our staff has linked the QD2010a to its A separate page which contains various commissioning webpage.

  • Page 7: Ubiquity Systems Software

    In this subsection you are able to set a couple of system baud is the factory default for all controllers AND the flags for the QD2010a itself. "Reboot Unit" sets a flag QD2010a). In addition, all controls must be programmed...

  • Page 8: Checkout And Troubleshooting

    1. Be sure to check and verify all wiring before powering the QD2010a. 2. Apply power. 3. If the QD2010a has not been pre-programmed, it can be programmed at this time. 4. The unit is now ready for operation. TROUBLESHOOTING...

Table of Contents