Sealey SA2001.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instruction
Manual
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
p
WARNING! Disconnect the equipment from the air supply before changing accessories, servicing or performing any maintenance.
p
Keep the equipment clean and maintain it in good condition (use an authorised service agent).

Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

WARNING! Ensure that the correct air pressure is maintained and not exceeded.
p
Keep air hose away from heat, oil and sharp edges. Check air hoses for wear before each use and ensure that all connections are
p
secure.
DO NOT install in direct sunlight or near any other heat source.

DO NOT direct air from the air hose at yourself, others or animals.

Drain the air tank daily. Water in the air line will damage equipment.

When work is complete ensure that the air supply is turned off.

If in any doubt about correct installation of this equipment consult a competent engineer.

2. INTRODUCTION
Suitable for most workshop air supply set-ups. Die-cast control heads with clear polycarbonate bowls. Regulator assembly features locking control
knob for pre-setting air pressure and large, easy-to-read pressure gauge. Filter is fitted with automatic drain tap. Lubricator includes oil/air mix
control and sight glass. Filter and Lubricator are fitted with protection bowl cage. (Model SA2001/FR.V2 and SA2001R are supplied with separate
wall brackets. SA2001.V2 has an integral bracket).
SA2001.V2
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . SA2001.V2 . . . . . . . SA2001/F.V2 . . . . . . . . SA2001FR.V2 . . . . . . . SA2001L.V2 . . . . . . . . .SA2001R
Port Size: . . . . . . . . . . . . . . . . . . . . . 3/8"BSP . . . . . . . . . . 3/8"BSP . . . . . . . . . . . . 3/8"BSP . . . . . . . . . . . . 3/8"BSP . . . . . . . . . . . . . . 3/8BSP
Maximum Working Pressure: . . . . . . 145psi . . . . . . . . . . . 145psi . . . . . . . . . . . . . 145psi . . . . . . . . . . . . . 145psi . . . . . . . . . . . . . . . . 145psi
Maximum Airflow: . . . . . . . . . . . . . . . 55cfm. . . . . . . . . . . . 48cfm. . . . . . . . . . . . . . 70cfm . . . . . . . . . . . . . . 55cfm. . . . . . . . . . . . . . . . . 80cfm
© Jack Sealey Limited
INSTRUCTIONS FOR:
AIR FILTER/REGULATOR/LUBRICATOR UNITS
MODEL NO'S:
SA2001/FR.V2, SA2001/L.V2, SA2001R
SA2001/F.V2 SA2001/FR.V2
Original Language Version
SA2001.V2, SA2001/F.V2
SA2001/L.V2
SA2001.V2,SA2001/F.V2,
SA2001/FR.V2,SA2001/L.V2, SA2001R
SA2001R
Issue:2 - 08/11/16