Advertisement
4.1.3.
Secure the upright supports (Fig.1B) already attached to the legs (Fig.1d), to the upright using a bolt, nut and washer part way up the
upright (not in picture).
4.1.4.
The unit must be bolted to the floor with four 1/2" anchor bolts, one at each end of the legs. This must be before the crushing unit is
secured.
4.1.5.
A fork lift truck or suitable crane should be used to raise the unit to its operational position. Remove the large nut and bolt from upper
part of the upright. Slide the mounting collars on the back of the crushing module onto the upright and align the holes in the upper
collar with the holes in the upright and insert the large bolt and secure with the nut provided.
4.1.6.
The oil collection tray has a 1/2" hose adaptor on its underside so the unit can be plumbed into a remote waste oil container.
4.2.
AIR SUPPLy.
4.2.1.
Connect the air supply to the air inlet on the air regulator mounted on
the right hand side of the unit adjacent to the door handle. The
inlet connection is 1/4"FnPT. The recommended air hook-up procedure
is shown in Fig.2
4.2.2.
You will require a minimum air pressure of 100psi.
WARNING! ensure the air supply is clean and does not exceed 190psi
‰
whilst operating the filter crusher. Too high an air pressure and
unclean air will shorten the product life, and may be dangerous, causing
damage and/or personal injury.
4.2.3.
drain the air tank daily. Water in the air line will damage the ram.
4.2.4.
Clean compressor air inlet filter weekly.
4.2.5.
line pressure should be increased to compensate for unusually long air
hoses (over 8 metres).
4.2.6.
Keep hose away from heat, oil and sharp edges. Check hose for wear,
and make certain that all connections are secure.
4.3.
FITTING DOOR HANDLE.
Place the handle shaft through the door from the outside and secure
with nylon washer and nut (Fig.3).
Note:
The door handle has a locking button and when fitting the handle it
should be configured so the locking button requires pressing to fully
latch or unlatch the door. The handle should be configured so the closed
(locked) position will leave the handle pointing downwards.
4.3.1.
Move the handle to the horizontal (open) position. Place the washer and door catch on the end of the door handle shaft pointing
downwards and secure with the screw (Fig.4).
5. OPERATION
5.1.
open air regulator and set pressure to a minimum of 100psi.
5.2.
Place the empty filter, open end downwards in the centre of the crushing chamber.
5.3.
Close the door ensuring the lock is full engaged. (The crusher will not function until the door is firmly closed).
5.4.
Turn the control lever leFT to the 'doWn' position and the piston will descend.
5.5.
When the crushing ram reaches the bottom the filter is crushed. You can also listen for the air to stop flowing (approx 30 seconds).
5.6.
Turn the control lever RIGHT to the 'UP' position, when the piston has returned to the start position move the control lever back to the
centre 'SToP' position.
WARNING! never attempt to open the door until the piston is fully retracted and the control lever is in the 'Stop' position.
‰
5.7.
open the door and remove the crushed filter. Close air regulator and disconnect air supply.
Note:
leave the door ajar when not in use.
6. MAINTENANCE
WARNING! All inspection and maintenance procedures should be carried out with the air disconnected and the ram retracted.
‰
6.1.
NORMAL MAINTENANCE.
6.1.1.
Persons using the crusher should be properly trained in its use including inspection of the unit prior to operation. If the operator is in
any doubt regarding the proper functioning or structural integrity of the unit it should not be used. Remove it from service immediately
and contact your local Sealey stockist.
6.1.2.
If the unit is used daily it should be further inspected by a qualified person on a weekly basis.
6.1.3.
If the unit is used intermittently it should be further inspected by a qualified person on a monthly basis.
6.1.4.
All warning labels, instruction labels, and specification labels should be complete and readable.
6.1.5.
external surfaces of the unit can be washed with a mild soap solution.
6.1.6.
Clean and/or remove sludge and other foreign matter from the crushing chamber after each use.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk business Park, bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey limited
01284 703534
sales@sealey.co.uk
Original Language Version
fig.2
nylon Washer
Wave Washer
fig.3
nut
www.sealey.co.uk
HFC08.V2 Issue 2 (HF) 10/10/18
domed Washer
Screw
fig.4
Advertisement
