Advertisement
4. ASSEMbLY
4.1.
Assemble the frame, feet and sucker units as in fig.1.
5.
opErATion
WArninG! Ensure that you read, understand and apply Section 1 safety instructions.
The suction cups are designed to work best on glass at a room temperature of 20ºC. Cold temperatures, humidity and other surface
contamination may reduce the holding capacity. Moisture and other contaminants will reduce the slip resistance of the cup.
WArninG! This is a hand tool and must not be used in conjunction with a crane or any other lifting device.
5.1
Ensure that the windscreen is clean, dry and free from oil and grease.
5.2
Remove the protective cover from the suction cups.
5.3
iF rEMoVinG A WindScrEEn: place the assembly over the glass.
5.4
Apply firm pressure towards the glass and work the pump plungers (fig.2) on the suction cups. When the suction is sufficient, the plungers
will stay in, concealing the red lines.
5.5. When all four cups have achieved full suction, it is safe to remove the windscreen.
5.6. Always keep the plungers in view during moving/lifting. Should the plungers begin to rise and the red line reappear, this indicates a loss of
suction and you should put down the load immediately.
5.7. Remove the windscreen and place the frame on its feet.
5.8. Pulling the release tag will destroy the vacuum and allow the windscreen to be removed. Use finger tension only to peel back the release
tag; using a sharp object to prise the cup will damage the rubber.
5.9. To inSTALL A WindScrEEn: place the kit with the suction cups upwards.
5.10. Check that the suction cups are clean and undamaged.
5.11. Lay the glass, having ensured that it is free of grease and moisture, on the suction cups and create vacuum in all four cups.
5.12. When attached lift the windscreen, with one person at either side, and place the glass in the prepared opening in the vehicle.
5.13. Release the windscreen as in 5.8 when it is secured to the vehicle.
noTE: The suction cups are designed for lifting, carrying and holding for a short period of time only. If circumstances cause the load to be held for
longer than expected, the grip must be checked frequently with reference to the plunger position and the visibility of the red line.
5.14. Refit the protective covers onto the suction cups and store the kit in a clean, dry, childproof location.
6.
MAinTEnAncE
6.1. Check the condition of the suction cups regularly, if damaged replace using genuine parts only.
6.2. Always keep suction cups clean and free of oil and grease. Clean regularly with a non-aggressive cleaner.
6.3. In order to preserve elasticity, do not expose rubber pads to sunlight over an extended period of time.
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable) into
approved containers and dispose of the product and the fluids according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMporTAnT: No liability is accepted for incorrect use of this product.
WArrAnTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
inForMATion: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
© Jack Sealey Limited
Environmental protection
Sole uK distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
fig.2
www.sealey.co.uk
01284 757500
01284 703534
sales@sealey.co.uk
AK98944
Issue: 1 - 08/04/14
Advertisement
