Intended Use; Safety Instructions - Kaiser Fototechnik 5850 Operating Instructions Manual

5850bed_0317_DIN A5.qxp_Layout 1 13.03.17 11:09 Seite 5
ENG LI S H
(1) Lighting unit
(2) Hinged bracket
(3) Adapter for 16 mm (5/8") standard spigot
(4) Foot
(5) Mains lead
(6) ON/OFF switch
(7) Slide-in foot
(8) Lock ring
(9) Lock ring
(10) Slide-in foot
(11) Mounting shoe
(12) Fastening screw
(13) 16 mm (5/8") standard spigot
(14) Bars
(15) Illuminated area
(16) Blocking screws for detent joints
Prior to using your light, please read these in-
structions carefully. Keep them safe to have
them at hand at any time. If you pass the light
on to somebody else, always include these in-
structions.

1. Intended use

The 5850 LED Desktop Light is intended to be
used exclusively for the illumination of photo
and video shots. It is not intended for household
lighting.
Use the light only as described in these instruc-
tions. Any other use has to be considered as not
as intended and can result in material damage
or physical injury. This light is not a toy.
Kaiser Fototechnik takes no responsibility for
damages caused by not intended or incorrect
use.

2. Safety instructions

Please observe the following safety instructions:
WARNING!
Disconnect the light from the mains when not in
use or before cleaning.
Keep the light away from children.
Do not put the light into operation, if housing,
cable or plug is damaged.
Do not look directly into the light for a longer pe-
riod of time, when it is switched on.
Do not disassemble or modify the light. Repairs
must only be carried out by qualified persons.
CAUTION!
Only use the light with parts designed for it.
Keep the light away from water and other liq -
uids and from combustible materials.
Make sure that the light is not covered during
operation.
Do not use or store the light at places with ex-
tremely high air humidity or at extremely hot
plac es. Keep the light away from long-standing
direct solar radiation.
Let the light cool down before boxing it.
3. Check light and scope of supply
(fig. A)
When unpacking the light for the first time,
please check if the scope of supply is complete.
It comprises:
- Lighting unit (1)
- Hinged bracket (2)
- Adapter (3) for 16 mm (5/8") standard spigot
- Foot (4)
Check also, if the light and the mains lead are
damaged by extraneous causes. Is this the
case, do not take the device into operation.
4. Setting up and positioning the
light (fig. B, C)
Unfold the two bars (14) of the foot (4).
Fit the adapter (3) on the 16 mm (5/8") standard
spigot (13) of the foot (4) and secure it with the
fastening screw (12).
Push the slide-in foot (10) of the hinged bracket
(2) into the mounting shoe (11) of the adapter (3)
and secure this link by rotating the lock ring (9)
towards the adapter.
Now push the light (1) into the other slide-in foot
(7) of the hinged bracket (2) and secure the light
by rotating the lock ring (8) towards the light.
For changing the height position or tilting the
light (1) please proceed as follows: Hold the
light with one hand. Loosen the 3 blocking
screws (16) of the detent joints with the other
hand by rotating them anti-clockwise and move
the light into the desired position. Now tighten
the blocking screws again.
To change the direction of the light beam loosen
the fastening screw (12) on the adapter (3) and
rotate it on the foot (4). Do not forget to tighten
the screw again.