Related Manuals for dallmeier DF3000AXS
Summary of Contents for dallmeier DF3000AXS
- Page 1 Installation and Configuration English Colour box camera (electr. Day/Night) DF3000AXS Rev. 1.0.0 / 080508...
- Page 2 All rights reserved. This document may not be copied, photocopied, reproduced, translated, transferred to an electronic medium or converted to a machine-readable form either whole or in part without first receiving written permission from Dallmeier electronic GmbH & Co.KG. We reserve the right to make technical modifications.
-
Page 3: Table Of Contents
DF3000AXS Table of contents About this document .................. 5 Validity ......................5 Documentation on the device ............... 5 Convention ....................5 Safety instructions ..................7 General notes ....................9 Scope of delivery ..................9 Transportation and packaging ............... 9 Appropriate use ..................... 9 Performance features ................... - Page 4 DF3000AXS Appendix ....................29 Menu structure .................... 29 Technical data ..................... 30 Technical drawings ..................31 Pin assignment interfaces ................32 9.4.1 DC auto iris interface for iris control ............32 Dallmeier electronic...
-
Page 5: About This Document
DF3000AXS About this document Validity This document applies to the colour box camera (electr. Day/Night) DF3000AXS. It has been produced on the basis of version 1.7 (software). Documentation on the device Commissioning The quick guide headed “Commissioning“ lists the most important steps for the connection and commissioning of the device. - Page 6 DF3000AXS IMPORTANT The word IMPORTANT denotes information for preventing damage, incorrect configurations or incorrect actions. NOTE A NOTE offers information on principles, special features and efficient procedure as well as general recommendations. Expression Expressions in bold and italics generally indicate a control element on the device (switches or labels) or on its user interface (buttons, menu entries).
-
Page 7: Safety Instructions
Do not make any modifications to the unit (neither to the software nor the hardware) without consulting Dallmeier electronic. Improper modifications can cause malfunctions or damages. Dallmeier electronic accepts no liability for damages resulting from unauthorized or improper modifications to the unit. - Page 8 DF3000AXS Do not open the unit Do not open the housing of the unit. There are no components inside the unit that require maintenance by the user. The inspection, maintenance and repair with an open housing must only be carried out by trained and authorized professionals (installer).
-
Page 9: General Notes
Transportation and packaging Store the original packaging for transportation at a later date. Dallmeier electronic is not responsible for damage resulting from unprofessional/improper transportation. The goods should only be shipped in their original packaging. -
Page 10: Warranty
DF3000AXS NOTE The electronic Day/Night switching is not realized through a mechanically switchable IR cut filter. Therefore, there is no ICR function available and hence no IR sensitivity. NOTE For detailled information please see the chapter Technical data. Warranty The warranty period is 36 months. -
Page 11: Notes On Operating The Camera
DF3000AXS Notes on operating the camera The camera is operated at 12V DC. The camera is designed for use with CS-mount lenses. A C/CS-mount adapter ring (5 mm) is required for use with C-mount lenses. Note the lens type before using it. When using C-mount lenses without an adapter ring, the camera could be damaged. -
Page 12: Views And Connection Assignment
DF3000AXS Views and connection assignment Views Fig. 5-1 DC auto iris lens (not included in the standard scope of delivery) Locking screw for back focus adjustment ring (2 mm Allen screw) ¼’’ tripod socket (on top and bottom side) CS lens mount and back focus adjustment ring... -
Page 13: Connection Assignment
DF3000AXS Connection assignment Fig. 5-2 12V DC input terminal (internal inverse-polarity protection) RS232 interface (for service purposes only) Video output (CVBS, BNC) H Power LED DC auto iris interface for iris control Selector (4-way joystick) K Enter button Dallmeier electronic... -
Page 14: Installation And Commissioning
DF3000AXS Installation and commissioning Requirements at the installation site The camera is designed for indoor use. If used outdoors, the camera has to be mounted into a corresponding weather-proof housing. Unfavorable local conditions may shorten the life of the product or lead to malfunctions. -
Page 15: Adjusting The Back Focus
Possible damage to the sensor caused by improper cleaning. Only use approved methods and products for sensor cleaning. For more information please contact the Dallmeier support. Remove the rear lens cap and the camera body cap. Screw the lens carefully into the CS lens mount (D). -
Page 16: Installation And Commissioning
DF3000AXS Adjustment for lenses with a variable focal distance (zoom) If the focus changes as the focal distance changes, please proceed as follows: 1 Point the camera at an object with sufficient contrast at a distance of approx. 2 m. - Page 17 DF3000AXS Connect the video output (G) via video cable (coaxial) to the monitor. WARNING Danger of death from electric shock. Disconnect the power supply unit from the mains socket before connecting the camera. IMPORTANT Possible damage to the camera caused by an inadequate po- wer supply unit.
-
Page 18: Preparing To Configure
DF3000AXS Preparing to configure The camera is supplied with factory settings which enable it to be used for most scenarios without further configuration. However, if required, certain camera properties can be configured using the camera menu. The camera can be configured directly using the Enter button (K) / Selector (J) or by means of the UTC Remote Box, the recorder or PView. -
Page 19: Dms Recorder
DF3000AXS DMS recorder Fig. 7-3 Camera Recorder Monitor NOTE This method requires a recorder with software version 5.3.1 or higher and a built-in FG-11 frame grabber card. PView Fig. 7-4 Camera Recorder PView station Monitor NOTE This method requires a recorder with software version 5.3.1 or higher and a built-in FG-11 frame grabber card, using PView version 5.6.0 or higher. -
Page 20: Configuration
DF3000AXS Configuration The configuration dialog is opened as follows: Direct: Press the Enter button (K) for approx. 2 seconds. UTC Remote Box: Press the OK button for approx. 2 seconds. DMS Recorder: Select Camera control > Open / Close menu PView: Select Camera control >... -
Page 21: Presets
DF3000AXS Presets The presets allow you to very easily adapt the camera --------------- Presets ---------------- configuration to the on-site conditions to achieve the best Previous Page. possible video picture. > Presets < Universal. > Brightness < Universal > is set as the preset at the factory. -
Page 22: Basic Functions
DF3000AXS As an alternative to the presets, the following settings can be manually changed to adapt the camera to the prevailing conditions: Brightness Select Brightness to adjust the image brightness. Gamma Gamma defines the brightness range within the color space and thus the differentiation between lights and shadows. -
Page 23: Cctv System
Linelock that are operated with a mains frequency of 50 Hz must be enhanced for scenarios with neon tubes. V-Phase After selecting the video level and synchronization you can adjust the V-Phase, if necessary. NOTE The V-Phase function is not supported by the DF3000AXS. Dallmeier electronic... -
Page 24: Horizontal Flip
Night Control < Off > Night Mode Color Night Control = Auto is set by default for the DF3000AXS. Night: max. Gain NOTE The Day/Night switching is carried out electronically and is not realized by a mechanical ICR function (ICR = IR-Cut Filter Mechanically Removable). -
Page 25: Image Functions
With Night Mode, you can select whether the camera will take color or black-and-white images at night. Night Mode = B/W (black-and-white) is set by default for the DF3000AXS. Night: max. Gain Night: max. Gain allows you to fix the limit for the maximum amplitude of the video signal in night mode. -
Page 26: Backlight
DF3000AXS NOTE To record camera images with maximum resolution the Dallmeier recorder should be operated in full picture mode and the camera should be set to Progressive Scan = On. 8.4.2 Backlight The Backlight function compensates for the silhouetting effect -------- Image Functions --------- of backlit objects (e.g. -
Page 27: Digital Zoom
DF3000AXS 8.4.3 Digital Zoom Select Digital Zoom = On.. and press the Enter button. -------- Image Functions --------- First set the zoom factor next to Zoom in the submenu. Previous Page. Progressive Scan Then change the values next to Pan and Tilt to change the Backlight >... -
Page 28: Exit Menu
DF3000AXS Manual Select Manual and press the Enter button to manually adjust the white balance. Exit Menu Three options are available to exit the configuration menu: Last Changes If you wish to save the changes made to the configuration, ------------- Exit Menu -------------- select the Save option next to Last Changes and press Previous Page. -
Page 29: Appendix
DF3000AXS Appendix Menu structure ----------------- 3000 ------------------ > Presets.. Basic Functions.. Image Functions.. Save / Exit Menu.. --------------- Presets ---------------- Previous Page. > Presets < Universal. > Brightness Gamma Auto Sharpness Saturation WB Offset --------- Basic Functions --------- Previous Page. -
Page 30: Technical Data
DF3000AXS Technical data Technical specifications Sensor 1/3" DPS sensor -CMOS- Signal processing 17-bit Digital Signal Processing Dynamic range 102 dB typical - 120 dB max. Video capture Progressive Scan Transfer format PsF (Progressive segmented Frame) Active pixel elements 720 H x 540 V pixel... -
Page 31: Technical Drawings
DF3000AXS Technical drawings Fig. 9-1 Fig. 9-2 Unit: mm Dallmeier electronic... -
Page 32: Pin Assignment Interfaces
DF3000AXS Pin assignment interfaces DC auto iris interface for iris control Fig. 9-3 9.4.1 DC auto iris interface for iris control Signal Control Control Drive Drive Dallmeier electronic... - Page 33 Approximation of the Laws of the Member States relating to Electromagnetic Compatibility 89/336/ EEC and the Council Directive relating to Low Voltage 73/23/EEC and 2006/95/EEC. The following company is responsible for this declaration: Dallmeier electronic GmbH & Co.KG Cranachweg 1 D 93051 Regensburg The measurements were carried out in accredited laboratories.
Need help?
Do you have a question about the DF3000AXS and is the answer not in the manual?
Questions and answers