Summary of Contents for Magnum 3005
- Page 1 CONTENTS file:///C|/Documents%20and%20Settings/Lauren/...ther%20stuff/magnum/3005%20word%20booklet.htm (1 of 12) [03/03/2003 10:16:31 PM]...
-
Page 2: Table Of Contents
Transfer parameters from one device to another Calibrating Correcting measurements against a known accurate source Calibrating Jigs Jigs into which the soldering iron and hot air pencil are inserted so the temperature can be measured for calibration purposes file:///C|/Documents%20and%20Settings/Lauren/...ther%20stuff/magnum/3005%20word%20booklet.htm (2 of 12) [03/03/2003 10:16:31 PM]... -
Page 3: Features
Never touch the heated nozzle or allow the hot air to blow against your skin • Never obstruct air flow as this can damage the heating element • Take all the appropriate safety precautions when using the 3005 Station and handpieces • No liability is undertaken by the manufacturer for applications other than those in the operating instructions, or for any applied modifications. -
Page 4: Startup
Err 1 to 4 (1=S/iron cold, 2=S/iron overheat, 3= H/air cold, 4= H/air overheat) • The 3005 SMD Rework Station will automatically start with the factory settings (S/iron 350°, H/air 400°, Air flow at 60% and energy saving active). SETTINGS •... -
Page 5: Removing Qfp/Sop
Insert the wire hook into the holder and place under the legs of the IC. Blow hot air onto the legs nearest the hook when the solder melts, carefully move the hook along under the legs. To avoid resoldering move the pencil in one direction only file:///C|/Documents%20and%20Settings/Lauren/...ther%20stuff/magnum/3005%20word%20booklet.htm (5 of 12) [03/03/2003 10:16:31 PM]... -
Page 6: Removing Plcc
Air nozzle 1.5mm round SM100401 • Stainless Steel blade SM300406 • Wire hook SM300409 • Lifting fork SM300407 • Solder braid SM300405 • Stainless steel wire SM300205 • Tweezers SM300402 • Blade holder SM300403 file:///C|/Documents%20and%20Settings/Lauren/...ther%20stuff/magnum/3005%20word%20booklet.htm (6 of 12) [03/03/2003 10:16:31 PM]... -
Page 7: Accessories
When the lock setting have been checked the values in the Range settings will be ignored Finally click on the Store data on PCCU and wait for the progress bar to stop moving and the completed block to appear Reset PCU. file:///C|/Documents%20and%20Settings/Lauren/...ther%20stuff/magnum/3005%20word%20booklet.htm (7 of 12) [03/03/2003 10:16:31 PM]... -
Page 8: Station Configuration
CONTENTS Configuring the 3005 Station This procedure transfers data from the PCU, which has been loaded using a PC, into the 3005 Station. The PCU can also be used to restore the station to the factory settings Procedure • Switch off the 3005 Station •... -
Page 9: Pccu Calibration
IT IS VERY IMPORTANT THE ABOVE PROCEDURE IS CARRIED OUT CORRECTLY. Calibrating the 3005 Station This procedure automatically calibrates the 3005 Station’s Soldering iron and Hot air pencil to the PCCU, which has been precalibrated to a certified source. file:///C|/Documents%20and%20Settings/Lauren/...ther%20stuff/magnum/3005%20word%20booklet.htm (9 of 12) [03/03/2003 10:16:31 PM]... -
Page 10: 3005 Station Calibration
CONTENTS Equipment required • A calibrated PCCU • The 3005 station with the Soldering iron and Hot air pencil • The Soldering iron and Hot air pencil calibration jigs • The RJ-12 to RJ-12 connecting cable Note: The calibration procedure must be carried out in a closed environment, as the slightest breeze will affect the accuracy. -
Page 11: Specifications
When the calibration is complete the Complete LED on the PCCU will light and the Station will display CAL • Disconnect the Station and jig’s from the PCCU. • Reset the 3005 Station for new values to take effect. SPECIFICATIONS Mains input voltage: 220V – 240V 50/60Hz Power consumption: 0.6 Amps... - Page 12 CONTENTS Manufactured and Designed by Lauren Manufacturing Co. Software designed by Spline Technologies. file:///C|/Documents%20and%20Settings/Lauren...her%20stuff/magnum/3005%20word%20booklet.htm (12 of 12) [03/03/2003 10:16:31 PM]...