Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Intellisystem ThermalTronix TT-1230S Series
- Page 1 ThermalTronix TT-1230S Uncool Thermal Imaging Monocular User Manual...
-
Page 2: Warning Cautious & Attention
! Warning Cautious & Attention Warning: It represents conditions or actions which can possibly cause people to be injured or dead. Cautious: It represents conditions or actions which can possibly cause monocular damaged or data loss. Attention: It represents valuable notes for users. Important information - Please read user’s manual before you use it. -
Page 3: Table Of Contents
Contents ! Warning Cautious & Attention ............1 Introduction ................3 Packing list ........................4 Optional device ......................4 Device chart ................5 2.1 Function Button ......................6 2.2 Connectors ........................7 Getting Started ................8 Inserting & Removing Battery ..................8 3.1.1 Inserting Battery ....................8 3.1.2 Removing the Battery ..................8 Useful Notes on The Battery ..................8... -
Page 4: Introduction
1 Introduction Welcome to choose our TT-1230S uncooled monocular Model TT-1230S-18-NVMB with 18mm lens，FOV 30.5°x22.9°（±5%） TT-1230S-37-NVMB with 37mm lens，FOV 14.8°x11.1°（±5%） Features TT-1230S function: 2 X digital zoom Hot white/hot black switch TF card for photo / record Calibrate manually 5 options for bright of screen Mini-USB data transfer PAL video output 1.8m anti-drop... -
Page 5: Packing List
Application TT-1230S with uncooled FPA and will directly show you thermal image with high sensitivity. High resolution B/W image and record in TF card for analyze future and it widely used in patrol. Security. Boarder check and so on in any bad circumstance 1.1 Packing list ... -
Page 6: Device Chart
2 Device chart Lens cover Batter cover cell （TFc） Lens and focal gear Knobs for batter cover Calibration button/power button 键 Key for record Display button/Bright button Zoom button/polar Key for photo button Wrist belt Eyeshades Access flap（data connector） eyepieces（screen） Screw of lens Connector Outlook... -
Page 7: Function Button
2.1 Function Button TT-1230S Function Key Schematic ：Calibration/Power Button Short Press for calibration；Long press button M (≥3s) to power on or power off. ! Note：Please cover the lens or facing the camera to a even target to make sure the camera can get well-distributed image ... -
Page 8: Connectors
2.2 Connectors The connector is hide in the rubber cover on the backside of the device. User can get Video Output, USB connector and Power in connector with plugging the special designed cable. The Plug of the Special Connector Designed Cable (Connector to the device) Special designed Cable Video Output... -
Page 9: Getting Started
3 Getting Started 3.1 Inserting & Removing Battery 3.1.1 Inserting Battery Unscrew & Open the Battery Cover Put the Battery into the battery Slot with the metal pins facing Down-side. Put the Battery cover back and screw it。 ! Caution: only standard battery can be used, or battery may be stuck, and apparatus may be damaged by incorrect voltage and so on. -
Page 10: Warning
Please Charge with the specified Charger。 ! Caution： Using battery must follow: Charge the battery before using or long-time conserving. Only use the specified charger. Do not make positive and negative ends short connected. Do not make metal touch the battery port. -
Page 11: Capture Thermal Image
with metal connect down. Insert the TF card into the seat till it is locked When unloading TF card, press the top of TF card slightly, and the card will eject a little automatically. Then take out the card slightly with fingers. open the battery cover to load/unload TF card ! Note: If the camera working without TF card, when press the Photo/Recording button, it... -
Page 12: Usb Operations
starts working and displays thermal image. 3. Remove the lens cover and aim to the target. Turn the focus wheel to adjust foci to capture the best thermal image. When detecting target, if the image is not uniformly distributed, you can close the lens cover or long press “... -
Page 13: Operation Guide
! Note: The above function is the optional update function, do not include in the standard performance. Note: PCCam driver installation instructions: 1 After startup, switch to PCAM mode according to the above instructions to, and then connect to a computer USB port. 2 When computer prompt that need install drive, select install driver from CD, select the computer operating system (2k \ xp (w7) \ xp (w7) 64) corresponding to the driver to install;... -
Page 14: Operation Interface
Figure 1 Figure 2 4.2 Operation interface 4.2.1 Interface introduction When stable image is displayed, the below interface will come out:... -
Page 15: Display And Hide The Brightness Setting Function
LOGO Brightness Polarity Battery Indicator indicator Figure 3 Battery indicator: Indicates the current battery situation. Indicates battery is full. Indicates battery is very low. Need to charge. 4.2.2 Display and Hide the Brightness Setting Function After the machines is start up, the LOGO, battery indicator, brightness information, polarity, the Zoom will disappear when there’s no operation for 3 seconds. -
Page 16: Zoom/Polarity
Figure 4 4.2.3 Zoom/Polarity When the machine is working, press , the image will be swifted between Hot black and Hot white. Keep press this button（≥3S）, the image will be Zoom to 2X. Show as Figure 5; Figure 5... -
Page 17: Video Recording
4.2.4 Video Recording When the machine is working, press to record video. ON the right sideofthe scree, it will show the time which had recorded and how long you can record. On the down left side, you will see the information of date, show as Figure 6. When the video file size reach to 500MB, it will become another file and keep recording. -
Page 18: Restart
Figure 7 4.2.6 Restart （≥3S）to close the machine，keep press again to start up the machine. Keep press ! NOTE：After the machine is closed, please wait for 10 second then to restart the machine for safety. 4.2.7 Automatic Sleep Instrument in the observation or recording mode, no key operation for 10 minutes, it will automatically close the eyepiece display and enters sleep mode, press any key except the Photo key will active the camera. -
Page 19: Technical Specifications
5 . Technical Specifications ThermalTronix Items TT-1230S-18-NVMB TT-1230S-37-NVMB Detector Detector type Un-cooled FPA micro-bolometer characteristics Array size/format 384x288 Field of view/min focus distance 30.5°x22.9° 14.8°x11.1° Spatial resolution(IFOV) 1.38mrad 0.67mrad ≤0.08℃@30℃ Thermal sensitivity Image Frame frequency 50/60Hz characteristics Focus Manual Zoom Spectral range 8-14μm Display... -
Page 20: Troubleshooting
6 Troubleshooting Please follow the below table to diagnose and solve the problem. If problem is still exited, please contact our service department Problem Cause & Solution Battery not installed or installed incorrectly →Install battery or re-install battery Battery is out of power.
Need help?
Do you have a question about the ThermalTronix TT-1230S Series and is the answer not in the manual?
Questions and answers