Arctic AG4 Manual

Galvanized gas spreader

Hide thumbs

page of 24

/ 24
Bookmarks

Quick Links

Download this manual

Galvanized Gas Spreader

Models AG4, AG6, AG8, AG10

10.5 HP Briggs and Stratton

11 HP Honda

Warning:

Do not exceed GVWR or GAWR with spreader and load. Overloading could result in an

accident or damage.

Read this manual and engine owner's manual before installing or operating the spreader.

Page 1

www.arcticsnowplows.com

Need help?

Do you have a question about the AG4 and is the answer not in the manual?

Questions and answers

Summary of Contents for Arctic AG4

Page 1 Galvanized Gas Spreader Galvanized Gas Spreader Models AG4, AG6, AG8, AG10 10.5 HP Briggs and Stratton 11 HP Honda Warning: Do not exceed GVWR or GAWR with spreader and load. Overloading could result in an accident or damage. Read this manual and engine owner's manual before installing or operating the spreader.
Page 2 1 (one) year after the date of purchase (except engine – see below). Arctic Equipment Manufacturing Corporation will replace or repair, at its election, without charge, any part which becomes defective within the period described above.
Page 3 This warranty is made only to the original purchaser. There is no other warranty expressed, implied, or statutory. The customer must register the equipment with Arctic within 60 days from the day of purchase using the online registration system found on the Arctic Equipment website www.arcticsnowplows.com/warranty...
Page 4 - Turn spreader OFF before filling, adjusting, cleaning, servicing or performing maintenance. - Servicing the sander without special tools and knowledge could result in personal injury. See an authorized Arctic dealer for service. - Driver to keep bystanders minimum of 25 feet away from operating spreader.
Page 5 Galvanized Gas Spreader the conveyor. A single V-belt connects Engine and gear box, and the gear box with the spinner shaft (picture 6, 14 & 15). The amount of sand and/or salt that is discharged is dependant on two factors. One is the engine RPM which is controlled by a throttle.
Page 6 Galvanized Gas Spreader k) For wiring information see page with wiring instructions. l) Optional - Refer to Hitch Mounted Spinner Shaft Guard installation instructions to further protect your sander from damage. Clutch Pre-run setup Clutches must be burnished before operation. We recommend the clutches be engaged/ disengaged a few times to break them in before being placed under load.
Page 7 Galvanized Gas Spreader Selection Of Lubricant Our gearboxes are normally filled up with oil of S.A.E. grade 80W90. Where a wide temperature range is expected, the synthetic oil MOBIL SHC 634 is recommended. Synthetic lubricants permit extended life time between drains. This is due to the increased resistance to thermal degradation or oxidation.
Page 8 Galvanized Gas Spreader 4) One on drive shaft coupling (Picture #13, Item #16 on Parts List) 5) One on split shaft coupling (Picture #5) It is advisable to clean the air filter element. It can be easily washed out and reused.
Page 9 Galvanized Gas Spreader Page 9 www.arcticsnowplows.com...
Page 10 Galvanized Gas Spreader Picture #2 Picture #1 Picture #4 Picture #3 Picture #5 Picture #6 Page 1 www.arcticsnowplows.com...
Page 11 Galvanized Gas Spreader Picture #7 Picture #8 Picture #9 Picture #10 Picture #11 Picture #12 Page 2 www.arcticsnowplows.com...
Page 12 Galvanized Gas Spreader Picture # 13 Picture # 14 Picture # 15 Optional Spinner Guard Page 3 www.arcticsnowplows.com...
Page 13 Galvanized Gas Spreader Installation of electrical throttle for Briggs & Stratton Engine Electrical Throttle for B&S Engine RC-38880 Item Part# Description Qty. 1411907 Throttle motor 1411910 Throttle pin Assembly HH-00013-074 #8-32 x 3/4" Pan Head Machine Screw HH-00340-019 #8 Locknut 90069-A Throttle mounting bracket Note: Mounting bracket needs to be installed using engine mounting bolts.
Page 14 Galvanized Gas Spreader Electrical Throttle Kit for Honda Engine RC-38880-01 Item Part# Description Qty. 1411907 Throttle motor 90086-A Throttle mounting bracket HH-00013-073 #8-32 x 5/8" Pan Head Machine Screw HH-00340-019 #8 Locknut 90045-N Retainer 90076-A Harness 90046-M Handle 90048-N 2/56 Screw 90049-N 2/56 Nut 90050-M...
Page 15 If B&S engine is equipped with egulator/rectifier (square box) and the light on control box stays on all the time, modify B&S control box as shown above.
Page 16 Galvanized Gas Spreader Picture #1 Picture #2 Page 6 www.arcticsnowplows.com...
Page 17 Galvanized Gas Spreader Picture #3 Picture #4 Page 7 www.arcticsnowplows.com...
Page 20 WIRING DIAGRAM FOR 8', 10' AND DUMP TRUCK SAND SPREADER 1. The control box 90020-A is to be installed under the dash. 2. Drill hole 1 1/2" in firewall of the truck to attach harness 90028-A to harness 90020-A. The cable with 3 wires goes under the hood to be attached to the solenoid (installed under hood of the truck). Second part of harness goes to the back of vehicle.
Page 21: Top View
Galvanized Gas Spreader Top View Drive detail for sander with gas engine Back View Apply Page 1 www.arcticsnowplows.com...
Page 22 Galvanized Gas Spreader Galvanized Sander AG6, AG8, AG10 With Gas Engine R04 Part # Description Quantity RM-33002-10.5HP Gas Engine, 10.5 HP, Briggs & Stratton RM-33002-H Gas Engine, 11HP, Honda 90117-C Mounting Plate 90118-A Top Bearing Plate 90089-M Electric Clutch 90090-N Pulley, 2.3"...
Page 23 Galvanized Gas Spreader Galvanized Sander AG6, AG8, AG10 With Gas Engine R04 Part # Description Quantity HH-00857-006 Hood Latch HH-00013-073 #8 x 5/8” Screw HH-00340-019 #8 Lock nut 90130-N Belt, Gas Engine to Clutch, A42 90129-N Belt, Gearbox to Spinner Shaft, A33 HH-00960-009 Bearing (to support gear box input shaft) 90168-A...
Page 24 Galvanized Gas Spreader Galvanized Sander AG6, AG8, AG10 With Gas Engine R04 Part # Description Quantity HH-00972-090 ½” -20 UNF x 1.5” HHCS HH-00972-091 ½” -20 UNF x 1.75” HHCS HH-00294-002 5/16”-18 Hex Nut HH-01149-008 5/16”-18 x 3.75” Eyebolt HH-00457-011 7/16”...

This manual is also suitable for:

Ag6 Ag8 Ag10