1. Manuals
  2. Brands
  3. Teldat Manuals
  4. Remote Control
  5. MTC+
  6. Installation manual

Teldat MTC+ Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Manual
Teldat S.A.
MTC+
Installation Manual
Copyright© Teldat Dm689-I Version 2.1 8/2018 Teldat S.A.
MTC+
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MTC+ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Teldat MTC+

  • Page 1 Manual Teldat S.A. MTC+ Installation Manual Copyright© Teldat Dm689-I Version 2.1 8/2018 Teldat S.A. MTC+...
  • Page 2 This publication is subject to change. Teldat S.A. offers no warranty whatsoever for information contained in this manual. Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv- ery, supply or use of this manual.

  • Page 3: Table Of Contents

    Table of Contents Teldat S.A. Table of Contents Important Information....... . 1 Chapter 1 About This Manual .
  • Page 4 Table of Contents Teldat S.A. A.3.4 220V Model ........

  • Page 5: I Important Information

    Important Information Teldat S.A. I Important Information Caution The information below contains guidelines that you must comply with for your personal safety. Follow all instructions carefully. • Please read the safety and electromagnetic compatibility information on the attached sheet before connecting the device.

  • Page 6: About This Manual

    • Technical specifications of the MTC+ and the pinouts for its connectors. 1.5 How is the information organized? The purpose of this manual is to collect all necessary information on how to install and connect MTC+ to a Teldat router.
  • Page 7 1 About This Manual Teldat S.A. Note The manufacturer reserves the right to make changes and improvements in either software or hard- ware of this product, modifying the specifications of this manual without prior notice. The images showing the front and back panels of the device are for information purposes only. Some small modifications may exist in the actual device.

  • Page 8: Introduction

    • Consecutive ID (herinafter ID):This is the ID for the MTC+. Each MTC+ connected to a single Teldat router must have a unique ID. To select the ID, simply increase the number.

  • Page 9: Connections

    3.1 Management Connection The MTC+ can be connected to Teldat routers through a flat RJ45 connector (on the side of the router) and an RJ11 connector (on the side of the MTC+) or through a USB to RS232 adapter (USB male connector on the router side) and an RJ11 connector (on the side of the MTC+).

  • Page 10: Single Management Connection Design

    3 Connections Teldat S.A. them). To check that there is connection between both devices, access the Router monitoring menu, select power-switch via Telnet and run the version all command. The connected devices should respond. If the device does not respond, please see the section on Troubleshooting.

  • Page 11: Cascade Management Connection Design

    To connect several MTC+ in cascade, the output management interface for all devices (except the first) must be con- nected to the input management interface of the next MTC+. The input management interface of the first MTC+ should be connected to the Teldat router and the output management interface of the last must remain unused (see figure below).

  • Page 12: Connecting The Management Router Powered By Mtc

    3 Connections Teldat S.A. Fig. 5: Normal Power Connection. 3.2.2 Connecting the Management router powered by MTC+ In this configuration, the MTC+ controls the router managing the MTC+. If you use this, please bear in mind that: • If you run the on command, the router is unavailable until you press the MTC+ Reset Button.

  • Page 13: Power-Switch Command

    4 Power-Switch Command Teldat S.A. Chapter 4 Power-Switch Command This command is found in the router monitoring menu (enter P 3 to access it). Once there, access the POWER-SWITCH monitoring menu by running feature power-switch . The available commands are displayed by entering “ ?” .

  • Page 14: Power-Switch Probe

    MTC+ loses power and another when it regains power. There is an optional configuration parameter to en- able a periodic trap linked to the MTC+power status. To access this feature, go to P 5 and access the POWER-SWITCH configuration menu by running feature power- switch.

  • Page 15: Appendix A Technical Information

    Technical Information Teldat S.A. Appendix A Technical Information A.1 Troubleshooting The following table will help you resolve problems during the installation of the device. If you cannot resolve an issue, please ask your distributor for additional information. SYMPTOM SOLUTION The Control LED does not blink for a few seconds when Check the main power connector.

  • Page 16: Connectors

    Technical Information Teldat S.A. connected. strange characters appear in the answers you get. Check that you don't have two MTC+ with the same ID. Check the management interface connec- tions(input/output). Press the Reset Button for all MTC+. You hear a constant noise and the Control LED blinks Disconnect the MTC+.

  • Page 17: Input Management Connector

    Technical Information Teldat S.A. A.2.1 Input Management Connector RJ11 Input Management Connector RJ11 PIN Tx (output) Rx (input) A.2.2 Output Management Connector RJ45 OUTPUT MANAGEMENT RJ45 PIN CONNECTOR Rx (output) Tx(Output) A.3 Technical Specifications Two models are sold depending on the power supply, a 110V model and a 220V model.

  • Page 18: 110V Model

    Technical Information Teldat S.A. A.3.3 110V Model Power Supply Connector C14 (male). Power Supply Voltage 90-130V AC. Input Frequency 47-63Hz. Maximum Input Current Maximum Output Current Controlled Power Supply Connector C13 (female). Internal Fuse 100mA 250V Fast Acting. Fuse (external) 5A 250V Slow Acting.

  • Page 19: Appendix B Regulatory Compliance And Safety Information

    Regulatory compliance and safety information Teldat S.A. Appendix B Regulatory compliance and safety information B.1 Recycling and the Environment Please do not, under any circumstances, throw away any MTC+ with normal domestic waste. Ask your local town hall for information on how to correctly dispose of them in order to protect the environment against e-waste. Always respect the current laws regarding waste material.

  • Page 20: Translated Safety Warnings

    Regulatory compliance and safety information Teldat S.A. B.2 Translated Safety Warnings MTC+ MTC+ MTC+ MTC+ MTC+...

  • Page 21: Compliance

    Regulatory compliance and safety information Teldat S.A. B.3 Compliance B.3.1 FCC Statement B.3.1.1 Federal Communications Commission Interference This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resid- ential installation.

Table of Contents