Summary of Contents for Nagra CDP
- Page 1 CDP & CDT player User manual P/N: – © – ©...
-
Page 2: Table Of Contents
“Scan” mode ................18 “Shuffle” mode ................ 18 “repeat” mode ................. 18 Repeat “A/B” mode ..............19 Maintenance ................19 Case cleaning ................19 Laser lens maintenance ............. 20 Technical specifications ..............21 Declaration of conformity ............. 22 Nagra – Concept CD player... -
Page 3: Important Safety Warnings
CD-V, CD-I, CD-ROM, PHOTO CD or DVD format discs. Warranty Audio Technology Switzerland SA, designer and manufacturer of Nagra products, certifies that this instrument was thoroughly inspected and tested prior to leaving its factory and is in accordance with the data given in the accompanying measurement protocol and test sheet. -
Page 4: Congratulations
Since its inception in 1951, Nagra builds products that continue to earn a reputation for delivering ultimate sonic performance. Numerous awards have been bestowed upon Nagra for its technical innovation, excellence in design and ®... -
Page 5: Installation
Installation Unlocking the playback mechanism Locking screws x 4 The Nagra CD player features a playback mechanism locking system for transport. Note the screws on your CD player may differ from the one shown on the picture. All CD players now come with metal screws. -
Page 6: Set-Up
The top cover of the CD player features three slots for isolation spikes. You can obtain an isolation spike kit for the following devices: CDC, CDP, CDT, PL-L and PL-P from your Nagra dealer. Remote control The RCU-II remote control requires a 9V battery. -
Page 7: Connecting The Acps Ii Power Supply
This allows for consistent earthing of the various audio components. In specific cases, using this connection can cause damage to your system. It is imperative to contact your Nagra dealer, who will be able to advise you on the usefulness of this connection according to your setup. -
Page 8: Audio Connections
The connection block is located either on the back panel, or on the right side of the unit. Please contact your Nagra dealer if you wish to change its position. Connection block – Analogue output group (Not connected on CDT) 1 –... -
Page 9: Front Panel / Controls
6 – 7-position brightness control 7 – Loading tray open/close control Main selector 1 – Main selector 2 – Function LEDs 3 – Play 4 – Pause 5 – Stop 6 – Off 7 – Remote control Nagra – Concept CD player... -
Page 10: Display
3 - Function modes: REPEAT, SHUFFLE, INTROSCAN, information or error messages. 4 – Time display: Current, total, remaining. When you load a new disc in Stop mode: the display indicates the total number of tracks and disc playing time. Nagra – Concept CD player... -
Page 11: Basic Functions
Then, position the clamp as shown in the picture. Your CD player is equipped with a clamp detection system. If you forget the clamp, a "NO CLAMP" message will appear on the display. Nagra – Concept CD player... - Page 12 - The current brightness setting is memorized when the unit is switched off and restored at power on. - When the display is off, pressing the control downwards lights up the display and front panel LEDs. Nagra – Concept CD player...
- Page 13 CDP and CDT. key: Provides access to the numeric keypad in section 2 of the remote control. NB: The CD player is set to device number 4 by default. You can ask your Nagra dealer to change this setting. Nagra –...
- Page 14 For instance: to select track 26, press the twice, then press 6. When selecting a track numbered between 1 and 9, you can speed up track access by pressing 0 before the required track number. For instance: 06. Nagra – Concept CD player...
-
Page 15: Advanced Functions
In Remote mode, you can use all of the remote control functions. The front panel is deactivated except for the Brightness control, OPEN/CLOSE control. To switch to Remote mode, set the main selector to the R position. Nagra – Concept CD player... -
Page 16: Advanced Functions Description
The absolute total time and total remaining time values cannot be displayed in the PROGRAM, SHUFFLE and REPEAT ONE modes. Please note: on some CDs negative time values may be displayed. This is a countdown between tracks. Nagra – Concept CD player... -
Page 17: Prog" Mode
Press the Stop key twice to cancel the program. All program entries will be erased. The ALL/ONE repeat function is available in Program mode. In this mode, the total program duration display is limited to 240 minutes. Nagra – Concept CD player... -
Page 18: Scan" Mode
“repeat” mode The Repeat mode – "REP" key on the remote control – allows the whole disc (REPEAT ALL) or current track (REPEAT ONE) to be played repeatedly. You can use this function in Program mode. Nagra – Concept CD player... -
Page 19: Repeat "A/B" Mode
To clean a CD, wipe it along straight lines from its centre to its edge with a soft, non-fluffy cloth. A cleaning product could damage the disc! Never write on or affix labels to a CD. Nagra – Concept CD player... -
Page 20: Laser Lens Maintenance
Clean the lens with a lightly impregnated cotton bud. Exert only a very small amount of pressure and imperatively follow the movement shown below. WARNING: Any other cleaning method could destroy the lens. Nagra – Concept CD player... -
Page 21: Technical Specifications
Technical specifications The following table shows the general specifications for all Nagra CD players. Your personal CD player measurements are provided on the accompanying "measurement protocol" document. Formats Ø 120 or 80mm CD Audio, CD-R, CD-RW Programming Up to 20 tracks... -
Page 22: Declaration Of Conformity
FABRICANT: Audio Technology Switzerland Orio 30A Romanel sur Lausanne Suisse MANUFACTURER: Audio Technology Switzerland Orio 30A 1032 Romanel sur Lausanne Switzerland APPAREIL : Nagra CDC – CDP - CDT MODEL: Nagra CDC – CDP - CDT NORMES APPLICABLES : APPLICABLE NORMS: Champ électromagnétique rayonné...