Rossi Bi KXH1024FS Installation Manual

Bi KXH1024FS

Features

- Automatic source 90V - 240V ~ ac
- Motor with maximum power 520W
- End of stroke sensor HALL and Reed Switch
- Internal memory for 1024 removable buttons
- HCS reception system, anti-cloning
- Frequency of reception 433 Mhz

- Acceleration adjustment

- Deceleration adjustment

- Aperture speed adjustment
- Closing speed adjustment
- Residential and building function
- Automatic electronic clutch
- Clears access key individual code
- Output for traffic light / garage light
- Entry for closing photocell
- Input for opening photocell
- Lock Output
- Adjustable automatic closing
- Opening and closing switch
- Independent closing switch
- Auto reverse function
N - Neutral / Phase 2
F - Phase (Electrical Network Input 90 ~ 240VAC)
CAP - Permanent Capacitor
U/V/W - Motor wires (U = Common, yellow wire)
--------------------------------------------------------------------------------------------------------
12V - Output 12VDC -300mA (for ROSSI accessories)
GND - Common for 12V Output and Accessories
FCH - Output for Locking Plate
PHOTOCELL - Input Photocell closing - RX TX (-) -
Negative Photocell FS
SIN LIGHT - Traffic Light / Garage
Light FA - End of opening stroke
CM - Common for Ends of Strokes and FF
Switch - Closing End of Stroke
BOT_A - Opening Switch
--------------------------------------------------------------------------------------------------------
GND - Common for Opening Photocell and FTA Closing Switch - Opening
Photocell
BOT_F - Closing Switch
N / F - Input 90 ~ 240VAC
1
Voltage input already intercepted by a 10A bipolar circuit
breaker and grounding the equipment.
CAP -Permanent Capacitor
Capacitor according to the motor power, the wires have no
polarity.

Ends of stroke:

3
The control unit automatically understands the two end-of-course systems, by contact (reed) and/or hall without programming.
NOTE: You should always use your own magnet for
hall sensor Ends of Stroke Reed CM-FA-FF
Randomly pick one end of each row of each end of stroke sensor and one forming a common one.
The other two ends will be FF (closed) and FA (open). Connect the wires to the respective terminals FF, FA and CM (common).
Observe the ends of stroke position on the drive so that the closed gate illuminates the red LED FF, and when the green LED FA is opened, it will light
up.
Sensor Hall End of Stroke
The hall sensor identifies the polarity of the magnets, north and south. Before fixing the magnets, identify the FA and FF by moving the magnet on
the rack until it passes in front of the hall sensor that will light the green led FA or red FF. (If both magnets light up the same led, reverse the
position of the magnet that does not match the chosen Open or Closed side.)
BOT_A/GND, The Opening Button consists of installing a buzzer (bell type) button on the terminal (BOT_A) of the control panel, interconnecting a receiver or an external
control system.
SIN -GND - Traffic light consists of interconnecting a traffic light with the central gate using the terminals SIN and GND.
LIGHT -GND - Garage light. to interconnect garage LIGHT accessory board, using the bornes LIGHT and GND.
BOT_A/GND, The Opening Button consists of installing a buzzer (bell type) button on the terminal (BOT_A) of the control panel, interconnecting a
4
receiver or an external control system. The single door closing function is activated after pressing and releasing the button.
Note: The Switch is used for manual activation in booths, activation by the intercom or possible need for remote activation by external button.
With SETUP to 1X (default function), BUTTON functions as "open-close" and BOT F only stops and closes.
With SETUP to 2X the BUTTON only opens and BOT F only closes after releasing the button of the switch.
FTA - Photocell opening
Photocell must be turned on in Normally NA (Normally Open) mode it only acts on the opening control not reversing the gate.
Code 13247 - Rev 05
FAIL SAFE
Installation Manual
FUNCTION
1-
1-BUILDING
2- 2-PAUSE
3-LOCK
3-
4-LV / PS
4-
5-DZ/BV
5-
6-FS
6-
Layout and
Components
GND - Coaxial Cable Mesh for External Antenna
ANT - Coaxial Cable Core for External Antenna / Internal Antenna Wire
Adjustments - Functional Settings Button / Path Recognition LEARN - Learn /
Delete Remote Control Button
ST - Led Event Indicator
FA - Green Led Open gate indicator
FF - Red Led Closed Gate Indicator
--------------------------------------------------------------------------------------------------------------
DIP-1 BUILDING- Building= ON / Residential = OFF
DIP-2 PAUSE - Auto Lock Enabled = ON / Disabled = OFF DIP-3 LOCK - Lock
/ Lock Enabled = ON / Disabled = OFF DIP-4 LV / PS - Heavy Gate = ON /
Light Gate = OFF
DIP-5 DZ / BV - Vertical Tilting= ON / Slider = OFF
DIP-6 FS - Fail Safe Function Enabled = ON / Disabled = OFF
--------------------------------------------------------------------------------------------------------------
ACEL - Acceleration setting DECEL-
Deceleration adjustment
VL.AB - Gate opening speed adjustment. VL.FC - Gate
closing speed adjustment.
Installatio
n
2
ADJUST
MENTS
U - V - W - Motor Wires
Note: Motor with maximum power up to 520W
The motor has 3 wires. The common (check label on the
motor) usually the yellow one must be connected to the U
output.
The outputs V and W determine the motor rotation direction
(right - left).
To do this test, leave the gate in the middle of the path (far
from the end of the course) and press, the LED FF or FA will
flash indicating the direction of rotation of closing or
opening.
Smart Products
Page01