Novacom V59 User Manual

Tv controller board

Hide thumbs

Table Of Contents

Quick Links

Download this manual

NOVACOM

User's Guide of V59 TV Controller Board

V1.1

2014-04-09

ELECREALM

http://www.elecrealm.com/

NOVACOM

Table of Contents

Need help?

Do you have a question about the V59 and is the answer not in the manual?

Questions and answers

Summary of Contents for Novacom V59

Page 1 NOVACOM User's Guide of V59 TV Controller Board V1.1 2014-04-09 ELECREALM http://www.elecrealm.com/ NOVACOM...
Page 2: Table Of Contents
NOVACOM http://stores.ebay.com/elecrealm/ Content Chapter 1--LVDS Cable Connection ......... 2 Chapter 2--Voltage Jumper ............5 Chapter 3--Refresh firmware............. 6 Chapter 4--Enter into Factory Mode and set LVDS Map number ....................11 Chapter 5--Mirror the image upside down....... 18 Chapter 6--Change the input source via remote controller..20 Chapter 7--Change the input source via keyboard ....
Page 3: Chapter 1--Lvds Cable Connection
NOVACOM http://stores.ebay.com/elecrealm/ Chapter 1--LVDS Cable Connection Please check the inserting condition of each foot. If some foot is not fully inserted (as shown in the figure below), please use tweezers to press the exposure to the top of the foot, let all feet be inserted into well.
Page 4 NOVACOM http://stores.ebay.com/elecrealm/ 3 / 28 NOVACOM...
Page 5 NOVACOM http://stores.ebay.com/elecrealm/ 4 / 28 NOVACOM...
Page 6: Chapter 2--Voltage Jumper
NOVACOM http://stores.ebay.com/elecrealm/ Chapter 2--Voltage Jumper 5 / 28 NOVACOM...
Page 7: Chapter 3--Refresh Firmware
NOVACOM http://stores.ebay.com/elecrealm/ Chapter 3--Refresh firmware 1. Please Prepare USB 2.0 Flash Memory Driver disk. 2. Please select the suitable firmware according to the resolution of your LCD panel. 6 / 28 NOVACOM...
Page 8 NOVACOM http://stores.ebay.com/elecrealm/ 3. Please copy the firmware to the USB 2.0 Flash Memory Driver disk. Make sure it only has one firmware file that you need refresh. 4. Plug in USB 2.0 Flash Memory Driver disk to the USB port of controller Board.
Page 9 NOVACOM http://stores.ebay.com/elecrealm/ 5. Plug in 12V DC Power Supply. 6. Wait a moment. You will see the Led becomes red and then becomes green. The Led will be flicker between red and green. The LED light 8 / 28 NOVACOM...
Page 10 NOVACOM http://stores.ebay.com/elecrealm/ is always in the blue after finishing the refresh of the firmware. 7. Unplug the power supply from the driver board. Then connect the 9 / 28 NOVACOM...
Page 11 NOVACOM http://stores.ebay.com/elecrealm/ LVDS cable and the LCD panel. Then plug the power to the power input again. Turn on the power by keyboard or Remote controller. 8. Then you will see the controller board can work with the LCD panel.
Page 12 NOVACOM http://stores.ebay.com/elecrealm/ Chapter 4--Enter into Factory Mode and set LVDS Map number If the LCD panel displays the image as below, the LVDS map should be changed. The operation only can be finished via the remote controller. 1. Press the “menu” button on the remote controller.
Page 13 NOVACOM http://stores.ebay.com/elecrealm/ 2. Then press number “1” “1” “4” “7” . 12 / 28 NOVACOM...
Page 14 NOVACOM http://stores.ebay.com/elecrealm/ 13 / 28 NOVACOM...
Page 15 NOVACOM http://stores.ebay.com/elecrealm/ 3. The LCD panel will display the following image: 4. Press “up/down” on the remote controller so that the cursor moves to “LVDS Map”. 14 / 28 NOVACOM...
Page 16 NOVACOM http://stores.ebay.com/elecrealm/ 5. Press “left/right--right” and go into LVDS Map. Then press “left/right” and change the LVDS Map number to the proper number, the LCD panel will go to the normal picture. 15 / 28 NOVACOM...
Page 17 NOVACOM http://stores.ebay.com/elecrealm/ 16 / 28 NOVACOM...
Page 18 NOVACOM http://stores.ebay.com/elecrealm/ 17 / 28 NOVACOM...
Page 19: Chapter 5--Mirror The Image Upside Down
NOVACOM http://stores.ebay.com/elecrealm/ Chapter 5--Mirror the image upside down Please enter into “Factory setting” by referring to images in Chapter 4 first. Then change the “MirrorEnable” value between “ON/OFF” by referring to the following images. In order to rotate the image 180 degrees, please turn off the power and then turn on it after changing “MirrorEnable”...
Page 20 NOVACOM http://stores.ebay.com/elecrealm/ 19 / 28 NOVACOM...
Page 21: Chapter 6--Change The Input Source Via Remote Controller
NOVACOM http://stores.ebay.com/elecrealm/ Chapter 6--Change the input source via remote controller 20 / 28 NOVACOM...
Page 22 NOVACOM http://stores.ebay.com/elecrealm/ 21 / 28 NOVACOM...
Page 23: Chapter 7--Change The Input Source Via Keyboard
NOVACOM http://stores.ebay.com/elecrealm/ Chapter 7--Change the input source via keyboard 22 / 28 NOVACOM...
Page 24 NOVACOM http://stores.ebay.com/elecrealm/ 23 / 28 NOVACOM...
Page 25 NOVACOM http://stores.ebay.com/elecrealm/ 24 / 28 NOVACOM...
Page 26 NOVACOM http://stores.ebay.com/elecrealm/ 25 / 28 NOVACOM...
Page 27: Chapter 8--Troubleshooting
NOVACOM http://stores.ebay.com/elecrealm/ Chapter 8--Troubleshooting Question 1 – The power adapter requirement of the board. The board voltage and the LCD voltage are 2 different parameters. The board can be worked from +5V to +12V with 3.0A current. Question 2 – The LCD panel voltage The LCD voltage only can be supplied by the board’s jumper with only +3.3V +5.0V +12.0V.
Page 28 NOVACOM http://stores.ebay.com/elecrealm/ If the blue image isn’t shown on the LCD, there should be problems and please don’t connect the signal cable to the board in order to save time. Please check the board power, the LVDS cable connection to board and to the LCD.