Baja Designs 448024 Manual

185 Bosstick boulevard phone 760-560-2252
san Marcos, ca 92069 fax 760-560-0383
Fog pocket installation
1.
Remove the five (5), 8mm inner fender liner screws as shown and remove the
lower portion of the wheel well. Screws located in positions
used in this location when reassembling.
1
2
3
8mm
1
2
3
DRIVER SIDE
1.
Position yourself under the truck. Remove the
Behind the grille kit!
bumper bolts on the back side of the bumper in
Your Car
the arrowed positions below.
16
1/4"-20 x 1.375" Bolt
17
1/4"-20 x 0.25" Bolt
18
1/4" Washer
16
19
17
18
1.
Remove the OEM screw at the arrowed location. Orient the bracket as
Reverse Kit
shown in region . Assemble the light with the S2 hardware to the
22
bracket. Adjust the bracket away from the exhaust tip as desired.
20
21
20
UNDER REAR BUMPER VIEW (DS)
2019 RAM
Select Models
info@bajadesigns.com
www.bajadesigns.com
2.
Use a 10mm wrench to remove the
indicated nut in region
socket and ratchet to remove the
and must be
4 5
indicated screw in region
fog light.
4
5
8mm
4
5
10mm
7
2.
REMOVE THESE BOLTS
3.
Attach the bracket to light bar as shown to the left. Then, replace the OEM
bumper bolts with the hardware shown in region
that the center of the lightbar is centered between the bumper parking sensors.
19
The Light Goes Here!
22
Exhaust
3.
Please be patient as this is a tedious step.
Use a T27 Torx or 5mm Hex bit in a 1/4"
7 . Use a 10mm
short socket & short ratchet to remove the
top 2 screws indicated in region
. Unplug the
8
space will be limited.
6
TOP OF BUMPER
Side View
7
8
BEHIND BUMPER VIEW DS
Locate this region when behind the bumper. Landmarks are indicated
on the image below. The bumper bolt is located behind the Bumper
Support Strut.
Bumper Support
Strut
Driver Side
Tow Hook
Driver Side
4.
Adjust the lightbar forward and slightly
downward. Tighten all hardware to fix
. Finally, adjust the bar so
19 in place. Place respective leads of relay
harness onto battery terminals, add
the extension harness, and finally plug
into the lightbar. Remove button switch.
Locate the rubber boot on the Driver
Side, make incision and feed the switch
through the firewall. Re-attach switch.
Enjoy the lumens!
2.
Repeat on the passenger side. Plug in the 2 pin
splitter to both lights. Then, plug in the wire tap
harness. Pull or cut back sheathing on the
Trailer Socket behind the bumper. Use the wire
tap on the Center Wire. There is a diagram on
the Trailer Socket cover shown on the right.
Ground the wire tap harness to truck frame.
3. 4.
1
Use a 7mm socket with an extension to remove the OEM fog
Grab a cold
2
light from the plastic bracket. Hold onto the OEM hardware and
one. You
plastic bracket.
deserve it!
. Hand
6
10
T27
5mm Hex
6
11
Top View
BD Coozie :)
FOG LIGHT ASSEMBLY (DS)
5.
10mm Mount the S2's with hardware as shown below. The S2 closest to the engine should
8
be mounted ~35/64" away from the nearest edge of the bracket. The other S2
should be mounted ~53/64" away from the nearest edge. Using the 7mm socket,
with extension, and the OEM hardware attach the Baja Designs bracket to the OEM
FOG POCKET FRONT VIEW
Take this moment to make sure the S2 resists
rotational and up down movement. The S2
should still be able to be adjusted with force.
Refer back to Step 4, 3, & 2 to install the Assembly.
6.
Pin the H11 Splitter with the polarity shown below. Plug the Baja Designs Splitter
into the pair of lights. Then, plug the H11 connector on the end of the splitter into
original fog light plug (H11). Tug on the connection. Test that the lights turn on.
Refer to Step 1 and re-assemble the inner fender liner. Repeat on the passenger
side.
PIN A
PIN B
2 Pin Wiring Polarity
7.
In select trims, the fog light will turn on when rotating the steering wheel past a
certain point in non off-road environments. Aim the lights downward to avoid
blinding drivers.
21
Thank you for choosing
Trailer Socket
9
7mm
12
plastic bracket in all available mounting
locations.
14
13
15
1/4"-20 x 5/8" Bolt
6mm Washer
1/4" Nylock Nut
POS (RED)
NEG (BLK)
H11 Connector
Enlarged for detail