ShoreTel ST Voice Switch Wall Mount Bracket Quick Install Manual

Introduction and Installing Brackets
The ST Voice Switch Wall Mount Bracket Kit Contains:
• One ST Voice Switch Wall Mount Bracket.
• Three drywall anchors for attaching the ST Voice Switch Wall Mount Bracket to
drywall.
• Three Phillips sheet metal screws for use with drywall anchors.
• Three Phillips round head wood screws for attaching ST Voice Switch Wall
Mount Bracket to a plywood wall.
About the ST Voice Switch Wall Mount Bracket
The ST Voice Switch Wall Mount Bracket is an accessory that is used to mount one
half-width ShoreTel ST Voice Switch on a wall. The front of the voice switch will
face to the right when mounted on the wall. This wall mount bracket is designed for
use with the following devices:
• ShoreTel Voice Switch ST500
• ShoreTel Voice Switch ST50A
• ShoreTel Voice Switch ST1D
• ShoreTel Voice Switch ST100A
• ShoreTel Voice Switch ST2D
• ShoreTel Voice Switch ST100DA
• ShoreTel Voice Switch ST200
WARNING: To prevent overheating and fire hazard, do not use the
Rack Mount Dual Switch Tray to wall mount the ST Voice Switches.
Installation Equipment
To install the ShoreTel Voice Switch, you need the following tool(s):
• #1 Phillips screwdriver
Preparing a Plywood Sheet for ST Voice Switch Wall Mount
Bracket
1.
Securely anchor a sheet of plywood to the wall and
underlying structure.
• The minimum wall area is 17.50 inches (444 mm) by
14 inches (355 mm).
• Minimum plywood size is 14.50 inches (368 mm) by
11 inches (279 mm).
• Minimum plywood thickness is 0.5 inch (13 mm)
2.
Punch three pilot marks in the plywood using the wall mount as a template.
3.
At the top pilot mark, insert one round head wood screw partially into the
plywood. Leave 1/8 inch (3.2 mm) of the screw shank exposed.
Preparing the Installation Surface
355 mm
(14 ")
63 mm
(2 - 1/2 ")
Preparing Drywall for ST Voice Switch Wall Mount Bracket
1.
The minimum wall area required for mounting a ST Voice Switch Wall Mount
Bracket is 17.50 inches (444 mm) by 14 inches (355 mm).
Minimum drywall thickness: 3/8 inch (10 mm).
Maximum drywall thickness: 5/8 inch (16 mm).
2.
Punch three pilot marks using the wall mount as a
3.2 mm
template to determine the mark placement.
(1/8 ")
3.
At each pilot mark, insert the screw-in drywall
anchors flush to the drywall.
4.
Insert one Phillips sheet metal screw at the top
position partially into the drywall anchor. Leave
1/8 inch (3.2 mm) of the screw shank exposed.
Placing the ST Voice Switch Wall Mount Bracket on the Wall
1.
Hang the empty ST Voice Switch Wall Mount Bracket over the Phillips sheet metal
screw you inserted at the top position, and then tighten the screw to affix the
bracket to the wall.
2.
Install round head screws in the bottom positions to secure the bracket to the wall.
444 mm
(17 - 1/2 ")
222 mm
(8 - 3/4 ")
54 mm
(2 - 1/8 ")
51 mm
(2 ")
317 mm
63 mm
(12 - 1/2 ")
(2 - 1/2 ")
3.2 mm
(1/8 ")
Mounting the Bracket and Specifications
Installing the ST Voice Switch into the ST Voice Switch Wall
Mount Bracket
1.
On the ST Voice Switch, remove
the right side top cover screw, as
shown in the image to the right.
2.
Align the slots on the left side of
the ShoreTel Voice Switch with
the tabs on the bracket, slide the
ShoreTel Voice Switch slots onto
the tabs on the bracket, and then
rotate the ShoreTel Voice Switch
into the bracket.
.
3. Re-install the right side top cover screw
to securely attach chassis to bracket.
ST Voice Switch Wall Mount Bracket Specifications
Feature Specification
Dimensions 14-5/16 x 10-7/8 x 1-3/4 inches (363 x 277 x 44 mm)
Weight 2.7 lbs. (1.23 kg)