Firefly Vegatouch Forest River Forester V1 Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Forest River Forester V1

Table of Contents

Summary of Contents for Firefly Vegatouch Forest River Forester V1

Page 1 Forest River Forester V1...
Page 2: Table Of Contents
Forest River Forester V1 Manual The information contained in this manual is a general overview of the Firefly system and is subject to change at any time. Table of Contents Touchscreen Overview Home Auto Gen Start (AGS) Settings Lights Climate Control Slides &...
Page 3: Touchscreen Overview
Touchscreen Overview Tap any icon from the vertical navigation menu to select the desired page. The currently selected page will always be listed in the top corner of the screen. This symbol will appear whenever a fault condition is present. Tap the triangle to visit the Network Diagnostics screen.
Page 4: Home
Home Buttons will turn Blue while a circuit is on and Grey once the circuit has been turned off. This color change is known as showing status. Individual light controls. Light Master controls all interior lights at once. When Light Master Off is pressed, it will remember which lights were on.
Page 5 Fluid Tank Readings (TruTank): LP Tank Readings: • • Displays in 5 percent increments. Below 25% will read “Low” and the • tank level will show as normal. Below 10% will read “Empty” and the • tank level will show Empty. From 25% to 75%, the tank level and •...
Page 6 House Voltage – the Generator Start - hold Start to start voltage coming from your the generator (1 second delay). house batteries. Note: Generator Stop – Hold Stop to stop Battery graphics will display the generator. Red if below 12V. Chassis Voltage –...
Page 7: Auto Gen Start (Ags) Settings
Auto Gen Start (AGS) Settings Tap to Enable/Disable AGS. A warning message will require action to Enable. Trigger Options – Automatically start the generator using specified voltage settings (Low Volts) or when A/C or Heat starts (HVAC). Select one or both triggers. If no triggers are selected, AGS will not run.
Page 8: Lights
Lights This screen will control the lighting for the entire coach, including the exterior. Tap any button to turn the desired light On/Off. Lights with up/down arrows are dimmable. Press and hold these buttons to ramp the brightness up or down.
Page 9: Climate Control
Climate Control Use the Arrows to select your desired set temperature. Current zone temperature/mode/fan speed indicator. Fan Only Mode – Available if HVAC is off. The fan will operate by choosing High or Low. Auto will turn the fan off. Cool –...
Page 10 Tap the buttons below to operate a Vent fan. Tapping the Lid Up button will open the fan without powering up the fan. Tapping Power (ON) will raise the lid, power up the fan and bring it to medium speed. Tapping Power again (OFF) will power down the fan.
Page 11: Slides & Awnings
Slides & Awnings Press and Hold EXT or RET to operate the Slide and Awning. Note – Parking Brake and Ignition are required to unlock full functionality for both the Slide and Awning. Tap to navigate to the Leveling screen.
Page 12: Leveling
Slides & Awnings/Leveling Auto Level – Tap to automatically level the coach. Tap Cancel (button status will change) to stop the operation. The corresponding red operational lights will illuminate to indicate which jacks have been extended and will stay illuminated until the jacks have been retracted. Press and Hold the arrows to Raise/Lower the leveling jacks as needed.
Page 13 Press and Hold the Up/Down arrows to raise/lower the Stabilizer jacks (for Non-Equalizer leveling systems).
Page 14: Settings
Settings Tap to navigate to the Vegatouch Mira connection screen. Tap to navigate to the Wireless Switch display screen. Tap to select between Fahrenheit and Celsius. Floorplan display. Tap to disable the touchscreen for 15 seconds for the purpose of cleaning. Tap to navigate to the Network Diagnostics page.
Page 15 Drag the slider to adjust screen brightness. Tap to visit the Display Colors page to customize the look of your touchscreen. When Auto Dimming is enabled, the screen will enter sleep mode after 60 seconds of inactivity. Tap anywhere on the screen to wake it up. Please note that even if Auto Dimming has been disabled, the screen will still enter sleep mode after 4 hours of inactivity during daytime hours (5am –...
Page 16: Mobile App
Settings/Mobile App Vegatouch Mira is a wireless control module that easily connects to any Android or iOS device to give total control to many electrical, electronic and mechanical systems in your coach. Pair any device with the coach’s built-in interface to monitor and control many coach components.
Page 17: Vegatouch Mira Setup
Vegatouch Mira Setup Notice: Make sure that Bluetooth is turned ON in your smart device settings before proceeding. Locate the Login Information: The login information can be found by clicking on the Mobile App button on the settings page of the touchscreen or from the Mira module’s label.
Page 18 Notice: iOS Setup Tips Turn on Bluetooth to allow Vegatouch Mira to connect to Accessories. If you do not have Bluetooth turned ON in your iOS settings you will see this screen. Do not click OK, you must click SETTINGS. Your Bluetooth Settings page will now appear and you should turn Bluetooth ON.
Page 19 App Settings: Access the App Settings page by tapping the triangle (at the bottom of the screen) to expose the Settings button. Tap the gear to visit the settings page. Tap the Temperature Units selection to choose between Fahrenheit and Celsius. System Information and Mira Name.
Page 20 If instructed by Firefly, tap Enable Remote Help for advanced technical support. Once enabled, provide the Session ID to allow Firefly to remotely connect to your Mira app (internet connection required). To disable Remote Help, simply tap the Session ID number from the Home page of your Mira app.
Page 21: Switch Panel Info
Settings/Switch Panel Info The color-coded Wireless Graphic and Signal Strength Value will identify the status of a wireless switch panel. • Green – Over 100 (Strong) • Yellow – 85-100 (Medium) • Red – Less than 85 (Weak) Red Wireless Graphic with a Zero reading – The switch is currently disconnected from the screen. It is likely that the battery inside your switch panel needs replaced.
Page 22: Wireless Switch Pairing
Wireless Switch Pairing Red switch indicator with a zero reading – The switch is currently disconnected from the screen. It is likely that the battery inside your switch panel needs replaced. The wireless switch panel in your coach will illuminate a green LED whenever a button is pressed. If the LED on your switch panel does not illuminate when you press a button on your switch, you will need to replace the 2032 coin cell battery.
Page 23: Network Diagnostics
Settings/Network Diagnostics Firmware/Faults: This screen will show the status of the Lyra screen and G12 panel. It will also display any current faults the system may be experiencing. Online G12: This screen will dislay all currently active G12 inputs and outputs. Active Output...
Page 24 AirCon: This screen will show status of the AirCon modules. Online Wireless Switch Pairing...
Page 25: Display Colors
Settings/Display Colors Tap from the selections below to select a preset color scheme for your touchscreen. Once selected, tap Apply to save and exit. Currently selected option.
Page 26: Options
Settings/Options From the Settings page, press and hold the Floorplan display for 5 seconds. Once you lift your finger, the Options page will appear. Tap to select the required floorplan and necessary options. Tap Apply to save and exit.
Page 27: Overcurrent Detection
Overcurrent Detection If an output on the G12 experiences an overcurrent fault, a lightning bolt graphic will appear at the top of the screen. Tapping the Lightning Bolt graphic will result in a Warning screen with a brief set of instructions.
Page 28: Ssp17 Switch Panels
SSP17 Switch Panels Your coach uses SSP17 switch panels to control lighting and other functions. Lights that are dimmable will have Up/Down arrows next to the icon. Press and hold these buttons to ramp the brightness up and down. SSP17 switch panels use wireless RF technology to communicate with the Lyra touchscreen.
Page 29: G12 Dc Panel
G12 DC Panel Your G12 control panel is the power distribution center for the coach. This panel receives the signals sent from your touchscreen/switch panels and performs the actions that have been requested by activating and deactivating the required circuits. Every circuit controlled by the G12 is numbered and listed on a black label (load list) which is usually mounted next to the G12 panel.
Page 30: Networking
Networking Your distribution panel and touchscreen connect via your coach’s RV-C network. Each component will have a NET LED that is used to show network status. If a NET LED is displaying anything other than solid green and some of the panel’s functions are not working, please use the keys below to determine the network status of your hardware.
Page 31: Network Status Indicators
Network Status Indicators Every component of the Firefly system uses an LED to communicate network status. Use the key below to determine the network status of your hardware. Panel Network Status Indicator – Applies to any device with a network indicator: Fast flashing Green Light (4 times/sec) –...
Page 32: Mira Net Led Status Key
Mira NET LED Status Key The NET LED on your Mira module can change color in different situations. Use the following key to determine the operational status of your module. Device has no power or has completely failed Fast flashing green (4 times/sec) Device is attempting to make initial connection to the CAN network and good files Solid green...