Related Manuals for SEA USA ORION 24V
Summary of Contents for SEA USA ORION 24V
- Page 1 International registered trademark n. 2.777.971 ORION BOX 24V INSTALLATION MANUALS AND SAFETY INFORMATION SEA USA Inc. 67411520 REV.02 - 05/2018...
-
Page 2: Important Safety Information
International registered trademark n. 2.777.971 IMPORTANT SAFETY INFORMATION GENERAL SAFETY PRECAUTIONS The following precautions are an integral and essential part of the product and must be supplied to the user Read them carefully as they contain important indications for the safe installation, use and maintenance. 1. -
Page 3: General Safety Information
International registered trademark n. 2.777.971 GENERAL SAFETY INFORMATION An appliance shall be provided with an instruction manual. The instruction manual shall give instructions for the installation, operation, and user maintenance of the appliance. The installation instructions shall specify the need for a grounding-type receptacle for connection to the supply and shall stress the importance of proper grounding. - Page 4 The installer shall follow the provided instructions thoroughly. SEA products must only be used to automate doors, gates and wings. Any initiative taken without SEA USA Inc. explicit authorization will preserve the manufacturer from whatsoever responsibility.
- Page 5 International registered trademark n. 2.777.971 5. The End of Type E. Type E (audible alarm) devices can no longer be used for entrapment protection. This change was made because the Type E device is really a warning device, not an entrapment-protection device. Also, all gate operator classes are now required to have an audio alarm that sounds when two successive obstructions are encountered via a contact-type system.
-
Page 6: Warning Signs
International registered trademark n. 2.777.971 GATE WARNINGS AND PRECAUTIONS GATE ARRANGEMENT The first thing to check is that the gate is in good running order as follows: a) The gate is rigid and straight and runs smoothly throughout its travel. b) That the inferior sliding guide-rail is perfectly straight and horizontal to avoid a derailment of the gate (fig. -
Page 7: Features And Specifications
2 Limit switch 3 Foundation plate for security. 4 Electronic control unit 5 General switch DIMENSIONS Fig. 2 ORION 24V FAST TECHNICAL FEATURES ORION 24V 120 V (±5%) 50/60 Hz 120 V (±5%) 50/60 Hz Power supply 130 W 160 W... -
Page 8: Mechanical Installation
International registered trademark n. 2.777.971 MECHANICAL INSTALLATION TYPICAL INSTALLATION 1) ORION operator 2) Concrete to build operator on 3) Photocells 4) Safety edge 5) Key switch 6) Travel gate stops 7) Radio receiver 8) Guide rollers 9) High speed ball beaming wheels 10) Warning notice inside... - Page 9 International registered trademark n. 2.777.971 CONCRETE PADS 1. Arrange a little square of concrete, see size in fig. 5, with a perfect levelling on which the motor reducer will be fixed with the special plugs (sizes see fig. 5) 2. Make sure that in the center of the concrete pad has been forseen an exit for a sufficient number of conduit (for all accessories like loop detectors, maglock, photobeam and others) 3.
-
Page 10: Chain Installation
International registered trademark n. 2.777.971 CHAIN INSTALLATION In the figures 7 and 8 it is possible to see the correct installation with opened and closed gate respectively; notice the obliged run of the chain inside the pinion group which must not be modified. Opened position Closed position Fig. - Page 11 International registered trademark n. 2.777.971 Fig. 11 Fig.13 Fig. 12 3. Install a fillet chain tensioner to two extremity of the gate to regulate the tension of the chain. Note: Execute this last operation with motor completely released using the provided special release key.
-
Page 12: Manual Release System
International registered trademark n. 2.777.971 MANUAL RELEASE SYSTEM WARNING: Always switch off the main power (120V) before servicing the operator To release the gate: - Open the red door in front of the operator to left or right ( Fig. 14). - Insert the hexagon “T”... - Page 13 International registered trademark n. 2.777.971 5. To install and adjust the limit switches in closing,see the following instructions: - release the motor - close the gate manually - act on the adjusting screw so that the microswitch can activate the contact with the cursor (Fig. 19) CURSOR MICROSWITCH MICROSWITCH...
-
Page 14: Periodical Maintenance
Packaging materials such as plastic bags, foam polystyrene, nails etc must be kept out of children’s reach as dangers may arise. NOTICE SEA USA Inc. can not be deemed responsible for any damage or accident caused by product breaking, being damages or accidents due to a failure to comply with the instructions herein. - Page 15 Products under warranty will be returned pre-paid by SEA. Recognized defects, whatever their nature, will not produce any responsibility and/or damage claims to SEA USA Inc and SEA s.r.l. Warranty shall not cover any required labor activities. Warranty will in no case be recognized if alterations and any other changes will be found on products.
- Page 16 International registered trademark n. 2.777.971 SEA USA Inc. 10850 N.W. 21st unit 160 DORAL MIAMI Florida (FL) 33172 USA Phone:++1-305.594.1151 Fax: ++1-305.594.7325 Toll Free: 800.689.4716 web site: www.sea-usa.com e-mail: sales@sea-usa.com...
Need help?
Do you have a question about the ORION 24V and is the answer not in the manual?
Questions and answers