Advertisement
Operating the Laptop Safe
Important : Please read the instructions thoroughly before beginning the set-up
procedure.
Dia 1
Locking Knob
LCD Display
Electronic Key Pad
Operating Instructions
Note: Please make sure that after you have opened
the safe for the first time, you change the PIN,
for security reasons.
Operating the Laptop Safe
1. Remove the 2 manual override keys and keep
them in a secure location.The keys are packed
in the plastic bag attached to the outside of the
door.
2. To open safe for the first time, Press "START" then
enter the factory preset code (159159)
A opening music will sound and the word "OPEN"
will appear on the LCD screen.
3. With LCD screen showing "OPEN", turn the door
knob clockwise and open the door
WARNING: NEVER keep the override keys inside the safe.
Programming your Personal Identification Number (PIN)
1. With the door open remove the White Cap (Dia 2) on the Reset Button. Press "START" button.
When the LCD screen shows "------" input your six digit PIN code and then press the Reset
Button again immediately. "IN" will show on the LCD screen followed by the PIN code you have
entered and an acceptance beep will be heard. You have now successfully entered your new
PIN code.
-1-
Keylock Cover
Concealed
Hinges
Dia 2
White Cap covering
Reset Button
Dia 3
Battery Cover
Reset Button
Operating the Laptop Safe
Please keep a copy of your PIN number in a safe place, in case you forget it.
2. The safe will now lock when you close the door and turn the knob anti-clockwise.
3. To open the safe again press the "START" key then input your PIN code. Allow the code to be
accepted (you will hear an acceptance sound and the lock will disengage). Turn the knob clockwise
and open the door.
4. To alter the PIN code at any time follow the instructions in section 1.
5. Screw the white cap onto the red reset button when your PIN has been set.
Note: If the safe door is not opened for more than 5 seconds after the correct PIN has been
entered it will automatically re-lock. Repeat step 3 above to re-open.
6. Low Battery Power
If when pressing the "START" OR Reset button the "LO-BAT" is shown up on the LCD screen,
please change your batteries immediately.
7. To set a management code or secondary PIN
You can set a master or management code on this safe. First, open the door with your PIN code.
Then, press the Reset Button on the inside of the door. When "------" is shown on the LCD screen
press the "START" button and enter a six digit code.
When "IN" is dislpayed and the acceptance sound has been heard your secondary PIN has been
successfully entered. Please keep a copy of your PIN number in a safe place, in case you forget it.
The safe can be used in the same way with the management code as with the main PIN code. To
alter the management code follow the above procedure again.
CAUTION:
If an incorrect PIN is entered the safe will not open, the word
"ERROR" will appear on the LCD screen and a beep will be
heard. If the wrong PIN is input 5 times consecutively the
whole system will stop working for 2½ minutes and a beeping
will sound.
Opening the Safe with the KEY
1. You can open the safe manually with the override key at
any time, i.e. flat batteries, lost/forgotten PIN.
2. Remove the Keylock Cover (Dia 1) insert the key and turn
the key anti-clockwise and at the same time turn the locking
knob (Dia 1) clockwise and then you can open the door
manually.
WARNING:
Please keep the keys in a secure place. We cannot supply
replacement keys for security reasons.
Securing Your Safe
You may wish to secure your safe to a fixed part of the house
(i.e. a steel panel or wooden beam). This can be achieved by
using 2 of the 4 rawl bolts supplied in the back of the safe or
using the 4 rawl bolts in the base of the safe.
Use the holes in the safe to mark where you need to drill.
Loosely attach the rawl bolts onto the safe with the nuts and
washers provided. Hold the safe over the drilled holes and
locate the rawl bolts into these holes (Dia 5). Tighten the nuts
from the inside of the safe to secure firmly.
Note :
The rawl bolts are packed inside the safe
Dia 4
Dia 5
-2-
Advertisement
