Elk -M1ZTS Quick Start Manual

INSTALLATION OF M1ZTS or ZTSR
1. Remove the cover from the base of the Interface.
2. Mount the base using a #6 x 3/4" sheet metal
screw though hole in center of circuit board.
NOTE: The Interface is not weatherproof. If
mounted outdoors, place under a roof or deck
overhang or in a weather resistant box. For
freezer monitoring or extreme conditions the
model with 7 ft. Probe model (M1ZTSR) is best as it
allows the interface to be mounted away from the
sensor (indoors) in a more suitable environment.
3. Turn the Control Panel power OFF.
4. Run a four conductor cable (max. of 1000 ft.) from
the Interface to the Control. Connect the wires
per and diagram steps below:
- Connect a Green wire from terminal ZN on the
interface to any unused Zone input terminal on the
main M1 board (Z1-Z16) or M1EZ8 (Z1-Z8). No
EOL resistor is needed.
- Connect a Red wire from terminal +12V on the
Interface to Aux. +12 Volt DC terminal on control.
- Connect a Black wire from terminal NEG on the
interface to NEG terminal on control.
5. After all connections are complete, place the
cover on the interface and turn the Control Panel
power ON.
Temperature
Sensor/Interface
with cover
removed
ELK-M1ZTS "Short"
Temperature Probe
ELK-M1ZTSR "7 ft."
Temperature Probe plugs in here.
This example shows the
Temperature Interface
connected to Zone 15.
However, any of the 16 main
zones will accept a
Temperature Interface.
Zone Def=033 Temperature
Auxiliary
+12VDC Power
Outputs
Master Power Switch (SW1),
disconnects AC and Battery
power from control
10/04
Calibration pads - DO NOT USE without
help from ELK Technical Support
CAL
+ -
T
Black
Green
Red
Four conductor cable from
Temperature Inteface to the Control
(Maximum distance: 1000 ft.)
ELK-M1
(Left Side Terminals)
Z9
NEG
Z10
Z11
NEG
Z12
Z13
NEG
Z14
Green
Z15
NEG
Z16
ZONE 16
2WIRE
NORMAL
SMOKE
JP1
TELCO SEIZED
DIALER ACTIVE
+SAUX
NEG
Red
+VAUX
NEG
Black
+VAUX
NEG
+VAUX
NEG
AC
16.5 V
AC
POWER
STATUS
REVERSE
BAT LEADS
SW1
JUMPER TO
START WITH NO
AC
Zone Temperature
Sensor/Interface
ELK-M1ZTS
ELK-M1ZTSR
APPLICATION:
Allows the M1 or M1EZ8 to monitor remote tem-
peratures. Rules are used to activate outputs,
dial phone numbers, deliver voice alerts, etc. A
sensor can be interfaced to zones 1-16 of the M1
or zones 1-8 of the M1EZ8. Unit available with
short or long (7 ft.) Probe.
Zone Temperature Sensor/Interface
ELK-M1ZTS
ELK-M1ZTSR
FEATURES:
•
Measures Temperature From: -50 to +140 F
•
Communicates to Control Over 3 Wires
•
Operates On Any Main Board Zone, M1 zones
1-16, M1EZ8 zones 1-8
•
Up to 16 Interfaces May Be Connected To An
M1, Up to 8 Interfaces To An M1EZ8
•
Interface May be Placed Up To 1000 ft Away
•
Suitable for Indoor/Outdoor Use in a Covered
Environment
•
Available with Short Probe (M1ZTS)
or with 7 ft. Probe (ELK-M1ZTSR)
SPECIFICATIONS:
•
Operating Voltage: 12 Volts D.C.
•
Current Draw: 10mA
•
Housing Dimensions: 2.375" x 1.25" x 1"
* * IMPORTANT NOTE * *
For full compatibility with the ELK-M1ZTS or ELK-
M1ZTSR the M1 or M1EZ8 Control must have
firmware version 4.2.5 or higher and the Elk-RP
Software must be version 1.4.1 or higher. Earlier
version firmware/software may appear to work
but will not produce accurate readings.
PO Box 100 • Hwy. 70W
BATTERY
+ -
Instructions Printed On Inside
(Short Probe)
(7 ft. Probe)
(Short Probe)
(7 ft Probe)
828-397-4200 Voice
828-397-4415 Fax
http://www.elkproducts.com
email: info@elkproducts.com
•
Hildebran, NC 28637 • USA