Advertisement
4.2.4 Temperature Adjustment
150F
In standby mode, press Button A to enter
preset temperature
150F
In temperature adjusting mode, press Button
to
the temperature.
Release Button when display reads the
temperature, and
will automatically
adjust to it.
Note: When screen displays arrow pointing to left or right this means the adjustment has already
reached its upper/lower limit. Settings will not be saved when the device is powered is off.
When
temperature is stable for 60 seconds, it will automatically enter sensing mode.
Temperature status will
to hold the required temperature
Arrows up-heating
Arrows down-cooling
4.2.5 Sleep Mode / Stand By Mode
When
s idle
When SSI-065 is in sleep mode for 360 seconds without any detected action, it will then enter
STAND BY MODE. STAND BY MODE will cut off the power until you enable the soldering iron
again by pressing button A.
When you pick up the SSI-065 when its in the SLEEP MODE, it will automatically resume to preset
WAKE UP TEMPERATURE.
4.3 System Parameters/ Default Setting
Parameter
Descriptions
This sets the input power for how you are
Inpt_Pwr
powering the iron.
Wrk_Temp
This sets the working temperature of the iron.
Slp_Temp
This sets the temperature of the tip during sleep
mode.
Slp_Time
This sets the number of seconds before the iron
goes into sleep mode.
Idl_Time
This sets the number of seconds before the iron
goes into standby mode.
This sets the increment in which the temp steps
Temp_Stp
up with each button click.
Off_Volt
This sets when the iron shuts off when the
input power reaches this value
Unit
This sets the display value for the temperature
This sets the screen orientation for right or left
Scr_Flip
handed use.
To change default settings with SSI-065 buttons, follow the below steps:
1. Plug in power.
2. After SSI-065 finishes the power on sequence, press button B to enter CONFIG MODE.
3. Use button A and B to navigate parameters.
4. When you see the parameter you wish to program, long press button A or B for 1 second to
enter the parameter adjustment.
5. After you set the parameter to the preferred value, the SSI-065 will commit and save the
change after 5 seconds. Any key presses will reset this timer.
To change default settings on a Windows PC, follow the below steps:
1. Connect SSI-065 micro USB to your Windows PC, the OLED screen will display "CONFIG". The
SSI-065 is now in the CONFIG MODE.
2. In Windows, the SSI-065 will be detected like a thumb drive. Open CONFIG.TXT file in the
detected USB drive.
3. You will be able to change all parameters to your preferred value.
4. Save the CONFIG.TXT file, disconnect the SSI-065, and the device is ready for use.
5. Soldering Iron Tip
5.1 Changing Soldering Tips
Note : When SSI-065 displays "sen-err", it means the soldering iron tip is not installed properly.
5.2 Choosing Soldering Iron Tips
The SSI-065 comes with TS-D24 soldering iron tip as standard. You can use different optional
tips for your hobby projects (sold separately).
SSI-D24
400F
In temperature adjusting mode, press Button B to
increase the temperature.
400F
150F
Release the button, the temperature will
adjust to the set up value.
sensed every 5 seconds.
horizontal lines-temperature
stabilized
The preset SLEEP MODE is 400°F (204°C).
Default
Adjustable Range
6S Li-Po
550°F
400°F
180 seconds
360 seconds
10
10V
°F
RT
1.Unplug SSI-065 before changing. Make sure the
tip is cold to avoid burns.
2.Loosen the tip set screw.
3.Pull out the tip,replace with another one.
4.Tighten the screw.
SSI-K
SSI-BC2
5.3 Soldering Iron Tip Maintenance
(1) Before switching off, tin the tip's soldering side with some solder and wipe off any excess.
(2) Do not leave the tip in high temperature for long time, which may cause permanent damage.
(3) Do not apply too much force while soldering. It can damage the tip.
(4) Do not use a rough or abrasive material to clean the tip.
(5) If the tip surface is oxidized and makes it hard to apply solder on it, you may use 600-800 grit
sandpaper or wipe the tip with Ethanol or Isotropy alcohol, heat up to 400°F (200°C) and
apply solder immediately to avoid oxidation again.
(6) Do not use Flux that contains high chlorine or acid, use only resin based flux.
5.4 Soldering Iron Tip Lifespan
A soldering iron tips lifespan is related to its maintenance and usage. Once used, it is not
covered by the factory limited warranty.
6. Trouble Shooting Guide
Problem 1: No Display
Problem 2:Every time when installing
a new tip , the temperature status
displays random numbers
Problem 3: Soldering iron
restarts automatically
Problem 4: Soldering iron is heating
up and cooling down simultaneously
Problem 5: OLED displays "Warning"
Problem 6: OLED displays "High-Vt"
Problem 7: OLED displays "Sen-err"
Problem 8: The tip doesn't work with
the solder
Problem 9: SSI-065 returns to
standby mode during operation
3S~6S
7. Firmware Update
220°F-840°F
220°F-400°F
In an event of firmware update for the SSI-065, follow the below steps:
60-900 seconds
1. Visit Maclan-Racing.com and download the latest SSI-065 firmware to your PC.
2. Press button A while connecting SSI-065 micro USB to your PC, the SSI-065 will enter UPDATE
100-900 seconds
MODE and display "Update" on the OLED screen. Windows will detect the SSI-065 as a new USB
drive.
1-25
3. Copy the firmware file to the USB drive.
4. Unplug the micro USB connector, power on the SSI-065 with your battery, and the SSI-065 will
10-20V
complete the firmware updating automatically.
°C/ °F
8. Warranty and Service
RT/LT
The SSI-065 has one year factory limited warranty on the control logic board. Please contact Maclan
Racing in the event of a warranty service. Please visit
Maclan-Racing.com or HADRMA.com for service inquiries.
Tips are consumable parts, once it's used, it's no longer convered by the warranty.
SSI-B2
Check: If the cable is broken
Check: Is there any data in USB CONFIG mode
Check: lf the screen needs to be replaced
Means the device is checking status, which is normal
Check 1: ls it properly plugged into the power source?
Check 2: ls the voltage too low?
(needs to be set up in the config file)
Check 1: Is the tip first time in use?
Check 2: Is the power cord in loose or a defective contact?
Check 3: Is the tip overheating? Set the temperature to an appropriate
level?
Check 4 : ls the soldering iron clean? refer to "Soldering iron tip
maintenance"
Check 1: Is the SSI-065 overheating?
Check 2: Is SSI-065 temperature higher than the maximum operating
temperature?
Check 3: Check all connections and ensure the tip is in proper condition.
Check: If the voltage is too high? (over 24V)
Check 1: Is the soldering iron installed propely?
Check 2: lf check 1 passes, then replace the soldering iron tip
1. Tip temperature is over 400°C
2. The soldering side of the tip is not applied with solder properly
3. Lack of flux during operation
4. Rub the tip against dry or high sulfur sponge or fabric
5. Tip touched organic material like plastic, silicone oil or other chemicals
6. Using impure solder or solder that contains low proportion of tin
Check 1: The power source could have a low operating voltage that
triggered voltage protection.
Advertisement
