EVA Logik ZW31 Quick Start Manual

3-Way Z-Wave Smart Dimmer Switch
• ZW31 •
Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applica-
tions. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network.
This Device supports Lifeline (association group 1) supporting 1 node for lifeline communication.
Group 1 must be assigned the Node ID of the primary controller where unsolicited notifications will be sent. The Z-Wave controller should set this
association automatically after inclusion.
Lifeline association only supports the "Device Reset Locally" function. Refer to the instructions of your controller for any available details on how this
can be set.
Convention Description
• Product introduction
Part 1.
Introduction
• Installation steps
• Wiring instructions
Part 2.
Wiring Diagram
• Single pole and 3-way wiring diagram
• LED indicator/ Button function
Part 3.
• Adding / reset the device ( Factory setting)
Manual Control
• Min & Max Brightness Value Setting
For more detials, please refer to the manual parts.
If you have any questions during installation,
Please contact us ask@nie-tech.com

Part 1. Introduction

Basic Operation
The connected light can be turned ON/OFF in two ways:
1. Manually from the front panel of the In-wall Switch
2. Remotely with a Z-Wave Controller
Manual Control
The Front Panel Paddle Switch allows the user to:
Turn ON/OFF the connected fixture
Air-Gap Switch:
The "air gap switch" will cut power to the device if it's pulled up. It's located
right below the main switch itself, often next to the LED. Pull up for Bulb
replacement, push down for normal use.
CHANGING THE COLOR OF THE PADDLE(OPTIONAL)
This step is optional. Before you start you may want to change the color of the
paddle to match your wallplate or decor.
1. Push side tabs in on one side and then the other to release paddle. Lift the
cover up and off.
2. Simply put the new paddle onto the switch by side tabs and snap securely
into place.Once this step has been completed please proceed to part 2 wiring.
A Few Quick Reminders
A quick note before we give out the wiring schematics. Please do not try installing this device if you are unsure of how electrical circuits operate
within your home. As exciting as it is to have a smart switch installed, it can be dangerous and even life-threatening if you do not install this
correctly. Please consult a qualified electrician if necessary. With that said, here are a few other warnings we'd like to point out for your safety:
HOW TO INSTALL THE WIRES
Ground
1.
Load
Traveler
1. Unscrew: carefully turn the screw counterclockwise to leave enough space for
the wire to be inserted. Do not unscrew the screws completely.
Line
Neutral
2. Press down: Once loosened, use your finger so it catches the thread.
3. Insert the wire: make sure the wire is completely straight, then insert it into the
terminal while holding down the screw. Do not wrap the wire around the screw!
Line (hot) — black (connected to power)
4. Tighten: Turn the screw clockwise to tighten the wire. Make sure the
Neutral — white
wires are locked!
Load — black (connected to lighting)
Note: There are 2 holes for each terminal can be used in the
Traveler — red/other
connection.You can use a jump wire or the second hole at the
(only in 3-way installations)
terminal to connect.
Note before installation
150W LED, 500W
1) The Z-Wave In-wall Smart Switch must not exceed
3½ in
2) The switch box required: 1-gang U.S. wall box. deep recommended,
with permanently installed fixtures.）
regular 3-way on/off
3) Work with for 2 locations control. It can only be connected with regular 3-way on/off switch, don't use a smart
switch or a dimmer switch! Couldn't work with an add-on switch!
4) The colors of your wires may not match the ones in our diagrams so please make sure you've
their source, not color only.
5) Please check your original 3-way wiring circuit in your home before installation, and then
the manual.
6) Install the smart switch in the switch box which directly connects to the power Line and Neutral.
requires a Neutral for installation
7) This switch , or the installation will not succeed.
8) Not recommended for fan.
switch x1 wallplate x1 wiring x1 screws x2
Contents
Convention Description
Part 4.
• Solutions to some common problems
Troubleshooting
Function description
• Locally button function
• LED indicator status setting
• Auto Turn-On/Off timer
• Association setting parameter
• Restore state after power failure
Part 5.
• Light off state setting
Parameter Settings
• Button function setting
• Multilevel minimum value can be set
• Association group
• Generic device class
• Command classes
Model: ZW31
Power: 120VAC, 60Hz
Frequency: 908.42 MHz
Maximum Load: 150W LED, 500W incandescent
(300W with both sides of heat sink tabs off)
Minimum Load: 5W for LED bulbs
Range: Up to 100 feet line of sight Operating
Temperature Range: 32-104° F (0-40° C)
For indoor use.
Specifications subject to change without notice
due to continuing product improvement
Approval: Z-Wave Plus Certified
4.
2.
3.
STRIP WIRE AT 3/8-1/2"
incandescent.
2¼ in
deep minimum.（The switch is designed only for use
identified all wires correctly
follow the wiring diagram option 1 or 2
If you have any questions, please contact us at
ask@nie-tech.com
Single-pole wiring
regular
Ground
3-Way switch option 1
regular 1
Traveler
common
Neutral
From source
( Line/Hot Neutral and Light/Load)
Ground
Traveler
based on
Neutral
in
Line
From source

Part 2. Wiring Diagram

1. Tool: Please prepare a flat head screwdriver.
Power
2. Turn power OFF at circuit breaker or fuse box.
Remove wallplate.
3.
4. Remove the switch mounting screws.
5. Disconnect the wires and label them after remove
the old switch.(Please use our sticker)
Line
6. Carefully remove the switch from the switch box. (DO
OUT TO LIGHT
NOT disconnect the wires.)
7. There are up to five screw terminals on the smart
switch, these are marked (Please check <HOW TO
Neutral
Load
INSTALL THE WIRES>)
8. Fix the wallplate with screws after wiring succeed.
Line
(Please use our screws.)
9.The Ground was excluded from the diagram to
simplify the illustration. Please Make sure all ground
wires are connected to all switches respectively.
From source
OUT TO LIGHT
Line
Neutral
Neutral
Line
Neutral
From source
Power
Neutral
common
Line
OUT TO LIGHT
(3-way switch)
regular 2
Line common
Box 2
Box 1
Don't change this
regular 3-way on/off switch
OUT TO LIGHT
regular
(3-way switch)
common
None-connection
(Just for 3-way switch)
Load Neutral Ground Traveler
Smart
Line
Switch
Neutral
IMPORTANT
1) Neutral required. If the box do not have a Neutral,
please stop! Connect the white wire to neutral
terminal(use a white jump wire form the package or
the second hole at the terminal to connect.)
2) Insert the Line wire to Line terminal and Load wire to
Load terminal. LOAD and LINE Can't be swapped,
please make sure to identify them correctly!
Smart
Switch
common Line
common
Neutral
IMPORTANT
1) Neutral required. If the switch box do
not have a Neutral, please stop!
Connect the white wire to neutral
terminal (use a white jump wire form
the package or the second hole at the
terminal to connect.)
2) Insert the Line wire to Line terminal
and Load wire to Load terminal.
LOAD and LINE Can't be swapped,
please make sure to identify them
correctly!
3) Install the smart switch in the switch
box which directly connects to the
power Line, Load and Neutral.
4) Only work with regular 3-way on/off
for 2 locations control. It can only be
connected with regular 3-way on/off
switch, don't use a smart switch or a
dimmer switch! Couldn't work with
an add-on switch!