Advertisement
Quick Links
Advertisement
Summary of Contents for Quipall 2-1-SIL
- Page 1 COMPRESSOR...
-
Page 3: Table Of Contents
OPERATING THE AIR COMPRESSOR Preparing for Start-up Starting the Compressor Checking the Safety Valve Running the Air Compressor Draining the Tank Storage CARE&CLEANING TROUBLESHOOTING SERVICE PARTS following symbols. - Page 4 dust...
- Page 5 Safety lnformation{continued) AIR COMPRESSOR AND WARNING: Do not attempt to mo<lity this tool or create PNEUMATIC TOOL SAFETY accessories not recommended for use with this tool. Any such alteration or modification is misuse and could □ Keep compressors as far from the spraying area as result in a hazardous condition leading to possible serious personal injury.
- Page 7 1 68...
- Page 8 Air Passage Drawing Air intake Pressure switch Safety valve Pressu re gauge Regulator Tank Filter Ball valve Air Compressor Model 2-1-SIL 2-1-SIL-AL 6-1-SIL 10-2-SIL Output @ 40 PSI 3.20 CFM 3.20 CFM 3.20 CFM 5.60 CFM Output @ 90 PSI 2.20 CFM...
- Page 9 Pre-operation(continued) Maintain a Clear Area Package Contents & Assembly It is very important that the Air Compressor is positioned so that there is adequate airflow around the machine. There must be at Package contents: least 2 ft. of obstacle-free space surrounding and above the Air ■...
- Page 10 Pre-operation(continued) Electrical Power ELECTRICAL SAFETY (SPEED AND WIRING) ■ The no-load speed of this product is approximately Electrical Power Requirements 1,680 rpm. This speed is not constant and ADANGER decreases under a load or with lower voltage. ■ For voltage, the wiring in a shop is as important as the motor's horsepower rating.
- Page 11 TOOL USAGE (Model: 2-1-SIL / 2-1-SIL-AL / 6-1-SIL)
- Page 12 Pre-Operation (continued) TOOL USAGE (Model: 10-2-SIL) = Intermittent = Continuous = Not Recommended Framing/ Inflation Finishing nailing Bolling Rooting Tool � ��� � � Brad Finishing Finished/Roof- Impact Heavy duty 1/2 in. and 3/4 " ir ra c e lnflator Stapler t h t nailer...
-
Page 13: Operating The Air Compressor
Operating the Air Compressor Save this manual for future reference. AWARNING This manual contains important instructions for operating this product. For your safety, and the safety of others, be sure to read this manual thoroughly before operating the product. Failure to properly follow all the instructions and precautions can cause you and others to be seriously hurt or killed. -
Page 14: Preparing For Start-Up
Operation Preparing for start-up WARNING: Risk of unsafe operation. Firmly grasp air hose in hand when installing or disconnecting to prevent hose whip. WARNING: Risk of unsafe operation. Do not use damaged or worn accessories. WARNING: Risk of bursting. Too much air pressure causes a hazardous risk of bursting. -
Page 15: Starting The Compressor
Operation (continued) Starting the Air Compressor WARNING: Risk of bursting. If any unusual noise or vibration is noticed, stop the air compressor immediately and have it checked by a trained service technician. NOTE: When using the regulator and other accessories, refer to the manufacturer's instructions. -
Page 16: Running The Air Compressor
Operation (continued) Running the Air Compressor WARNING: Always ensure the switch is in the OFF position and regulator pressure gauge reads zero before changing air tools or disconnecting the hose from the air outlet. Failure to do so could result in possible serious personal injury. -
Page 17: Draining The Tank
Operation (continued) Draining the tank WARNING: Risk of unsafe operation. Air tanks contain high pressure air. Keep face and other body parts away � l,ll from the drain outlet. Use eye prote _ ction [ANSI 287.1 (CAN/ CSA 294.3)] when drammg, as debris can be kicked up into the face. -
Page 18: Care&Cleaning
CARE & CLEANING... -
Page 19: Troubleshooting
Customer Support. or needs adjusting. pressure (8 bar or 116 PSI) and the safety valve vents air. Manufactured for Quipall@/ CPO Commerce, LLC 120 W. Bellevue Drive, Pasadena, CA 91105 © 2018 CPO Commerce, LLC Made in China Customercare@quip-all.com... - Page 20 2-1-SIL � � -------- part list "'""'' ,..,. bolt "'" cylinder heed nhe plate " Clll)IICitorocne:r " ..•• " """"°"" bolt bolt UDloedina ttibe left fan Deflaticmalff .., pro tect COTI'1" " apriJII' l.t'toramoas, "' """""ingrod " bolt bolt...
- Page 21 2-1-SIL-AL...
- Page 22 6-1-SIL EWS30 41 D e f la tio nva l ve 51 unl o adi ng tube 61 01 covery 11 cylinder head 21 right fan rotator pipe 42 regulator 02 left fan wheel bolt 22 shaft seal 53 tank stator 03 leftcrankcase 13 obtura t ingr ing 23 bearing6908-22...
- Page 23 10-2-SIL part list 01 self tapping 11 bolt 21 limitedblock 31 right cankcase 41 elbow 51 capacitor 61 nut 71 safety valve 02 covery 52 1)1ug 12 cylinder 22 valve 62 drain cock 03 left fan 13 obturatingring 23 valve plate 33 bolt 43 connect 53 tank...