CONTENTS NECESSARY TOOLS……………………………………………………………...…… REPAIR MANUAL – 352 SCOREBOARD MODELS WITH RADIO CONTROL I : SCOREBOARD Problem No 1 : The control console is off and there is no time display on the scoreboard .... 4 Problem No 2 : The fuse burns out continuously ............... 5 Problem No 3 : The horn sounds continuously ................
I : SCOREBOARD PROBLEM No 1 : The control console is off and there is no time display on the scoreboard Check the mains power supply (230 VAC) to the scoreboard Power supply problem in the Voltage sport hall (check the circuit OK ? breaker at the mains) Check the scoreboard fuse...
Page 5
Check the voltage coming out of the power supply PCB 24 volts DC. Replace the power supply Voltage PCB in the scoreboard. See appendix P19 OK ? See appendix P18 Replace the PCB in the scoreboard. 5/28...
PROBLEM No2: The fuse burns out continuously Open the electronic rack of the scoreboard. Disconnect the horn connector off the PCB and replace the fuse. Wait for a moment then check the fuse again. Replace the power supply Fuse OK ? See appendix P19 Replace the horn See appendix P20...
II : CONTROL CONSOLE PROBLEM No1: The control console displays nothing Check the voltage 230V on the socket on which the charger is connected Power supply problem in the sport hall (check the circuit Voltage breaker in at the mains) OK ? Check the condition of the transformer plug and its voltage (≅...
Page 8
Voltage Replace the transformer OK ? Check the connection of the battery in the control console Connection Re-connect the battery OK ? Put the control console on charge for 48 hours then put it on again Control console Replace the battery OK ? ee appendix P22 Replace the PCB in the control...
PROBLEM No2 : The control console displays a line on top of the LCD Replace the LCD Replace the control PCB in LCD OK ? the control console See appendix P21 Problem No3 : The datas are displayed on the LCD but the keys of the control console do not work Check the connection of the...
III : PROBLEMS ENCOUNTERED WHEN THE SCOREBOARD IS RUNNING (control console programmed, timer launched in count down). PROBLEM No 1 : The control console displays the information, but nothing is displayed on the scoreboard (Please stand 15 meters away from the scoreboard) Check the condition of the antennas (scoreboard and control console).
Page 11
Press button 27 Choose channel 6 Go back to the sport mode Replace the control PCBs (with a new frequency) in the control console and Display in the scoreboard. (please contact OK ? Stramatel) See Appendix P18 and P21 11/28...
PROBLEM No 3: The control console and the scoreboard display the same information, but the horn doesn’t work Programme the control console and choose Basket-Ball, then launch the timer. Keep pressing button “HORN” Check the voltage 230 V AC at the horn connector See Appendix Replace the control PCB in...
Page 13
PROBLEM No 4: Incomplete LED-digit A LED-segment is missing on a digit : Check the connection between the flat cable and the digit. Check the condition of the pins of the flat cable connector. Replace the flat cable Connection connector, or replace the flat OK ? cable Replace the LED-PCB (Check the...
Some digits or some LED-segments are off : Check the connection between the flat cable and the digit. Check the condition of the pins of the flat cable connector. Replace the flat cable Connection connector, or replace the flat OK ? cable.
GLOSSARY PCB: Printed circuit board (electronic circuit board) LCD :‘’ Liquid Crystal Display’’. Screen (with liquid crystals) which displays the information of the control console Keyboard flat cable: Cable connecting the keyboard and the control PCB of the control console. LED : Light emitting diode Digit segment : Line of LEDs (a digit being made of several segments) Scoreboard flat cable: Cable connecting the LED-PCBs to the control PCB of the scoreboard.
Page 17
CONTENTS Replacement of the control PCB in the scoreboard Replacement of the power supply Replacement of the horn Replacement of the PCB in the control console Replacement of the battery pack Replacement of the LCD-Display Replacement of a LED-PCB Check the keyboard Program updating of the control console Program updating of the scoreboard In any case, the cost involved for setting the scaffolding up and down, will be supported...
Push the rack back up into the scoreboard, and fix it into place with the two nuts (E). Switch on the mains supply to the scoreboard, and test it with the control console. Return the faulty PCB to STRAMATEL for analysis. Work time : 30 minutes...
Push the rack back up into the scoreboard, and fix it into place with the two nuts (E). Switch on the mains supply to the scoreboard, and test it with the control console. Return the faulty power supply to STRAMATEL for analysis Work time : 30 minutes...
Slot and fix the new horn. Slot the horn grill into place and screw it. Switch on the mains back onto the scoreboard and test the horn. Return the faulty horn to STRAMATEL for analysis. Work time : 30 minutes Black Alu-cobond...
Close the control console (make sure you don't screw the big screws (B) in place of the small Ones (C)). Plug in the battery pack, place it in its spot, and screw back the trap door. Return the faulty PCB to STRAMATEL for analysis. Work time : 30 minutes X3324-X...
Unscrew the screw (A), take gently the battery pack out, and unplug its connector. Connect the new battery pack, place it in its spot, and screw back the trap door. Return the faulty battery pack to STRAMATEL for analysis Work time : 15 minutes...
Page 23
Close the control console (make sure you don't screw the big screws (B) in place of the small ones (C)). Plug in the battery pack, place it in its spot, and screw back the trap door. Test the control console. Please send the faulty LCD to STRAMATEL for analysis. Work time : 30 minutes X3324-X 23/28...
Put the 4 angles back into place (b) and screw the 8 screws (a). Switch the mains back to the scoreboard, and test it with the control console. Test the scoreboard. Return the faulty LED-PCB to Stramatel for analysis. Work time: 30 minutes TRAMATE...
Page 25
REPLACEMENT OF THE LED-PCB Val 1 Val 5 Val1 Val 1/5 Val 2/6 Val 2 Val 6 Val1 Val2 Val2 Val 8(c) Val 4 Val 8(f) Val3 Val3 Val4 Val4 N°1 N°2 N°12 N°3 Val5 Val5 Val 8(a/d/g) Val 8(b/e/h) Val6 Val6 Val1...
CHECK THE KEYBOARD For example : Press Button No 1 Check the resistance between pins No 5 and No 12 of the connector. 3324 3 4 5 10 11 12 13 26/28...
Page 27
Slot the new micro-processor into place (respecting its direction) (C). Plug the battery connector on the circuit board (A). Close the control console, and screw the five screws. Test the scoreboard. Return the faulty micro-processor and the nipper to STRAMATEL. Work time: 15 minutes X1248-X CLAVIER...
Page 28
Pusch the rack back up into the scoreboard, and fix it into place with the two nuts (E). Switch on the mains supply to the scoreboard, and test it with the control console. Return the faulty micro-processor and the nipper to STRAMATEL. Work time: 15 minutes...
Need help?
Do you have a question about the 352 Series and is the answer not in the manual?
Questions and answers