1. Manuals
  2. Brands
  3. MORLEY-IAS Manuals
  4. Repeater
  5. ZXr-A
  6. Operation & installation manual

MORLEY-IAS ZXr-A Operation & Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ZXr-A
ZXr-P
www.acornfiresecurity.com
www.acornfiresecurity.com
Document No. 996-144 Issue 02
operation &
installation
manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZXr-A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for MORLEY-IAS ZXr-A

  • Page 1 Document No. 996-144 Issue 02 ZXr-A operation & installation ZXr-P manual www.acornfiresecurity.com...

  • Page 2: Table Of Contents

    IQUID RYSTAL ISPLAY LED I ........................11 NDICATORS ................12 ONTROL USHBUTTONS AND WITCH 4.3.1 Test Key (ZXr-A Only)....................12 ..........................13 UZZER LCD M ..................... 13 PECIAL ESSAGES SPECIFICATIONS ........................14 Table of Figures 1 - B ..............5...

  • Page 3: Introduction

    • These instructions cover the operation and installation of the ZXr-A / ZXr-P Repeaters. Refer to the Fire Alarm Control Panel (FACP) Manuals for instructions on powering up, operating and programming the system.

  • Page 4: Description

    The ZXr-P Passive Repeater will only show (repeat) the operational state of the FACP. • The ZXr-A Active Repeater will show (repeat) the operational state of the FACP and can control the FACP using the SOUND ALARMS, SILENCE / RESOUND, MUTE BUZZER, ACCEPT and SYSTEM RESET functions.

  • Page 5: Mounting The Repeater To The Wall

    ZXr-A / ZXr-P Repeaters MORLEY-IAS Mounting the Repeater to the Wall • The ZXr repeater should be wall mounted in a position that allows clear visibility of displays and easy access to operating controls. The height above floor level should be chosen such that the LCD is just above normal eye level (approximately 1.5 metres).

  • Page 6: Direct Mounting

    Ensure correct orientation. This label is not used on the ZXr-P. • At position C, insert the MORLEY-IAS logo legend label. Ensure correct orientation. Figure 4 – Label Insert Locations Page 6 of 16 Document No.

  • Page 7: Installation Wiring

    Only terminate the repeater power cables at the FACP or external source after ALL pre- commissioning checks have been performed. Only connect power cables when the system power is OFF. • The ZXr-A / ZXr-P Repeaters must be RIBBON CABLE supplied with DC Power from an approved (INTERNAL)

  • Page 8: Rs485 Communications

    MORLEY-IAS ZXr-A / ZXr-P Repeaters 3.3.2 RS485 Communications Before commencing installation of the RS485 communications wiring, check to which type of panel the repeater is to be connected. If the repeater is to be connected to a ZX Series FACP, peel off and affix the supplied re-legend label over the text on the Termination PCB (see opposite).

  • Page 9: Address Setting

    ZXr-A / ZXr-P Repeaters MORLEY-IAS 3.4 Address Setting • Set the repeater address in binary using the address switch on the repeater chassis assembly PCB. (See Figure 9 above). • The address can be set in the range 1 – 126.

  • Page 10: Commissioning

    MORLEY-IAS ZXr-A / ZXr-P Repeaters 3.5 Commissioning 3.6 Preliminary Checks • Carry out the following preliminary checks for EVERY repeater being commissioned prior to power up the system. Check that all cables brought into the repeater have been terminated correctly. All power and signal cabling and wiring must conform to the appropriate local regulation.

  • Page 11: Operation And Controls

    Fire Alarm Control Panel (FACP) and the installation. • In addition, the ZXr-A is equipped with a key operated switch and five CONTROL keys and a TEST key. • The operation of the Repeater is as follows: 4.1 Liquid Crystal Display...

  • Page 12: Control Pushbuttons And Key Switch

    MORLEY-IAS ZXr-A / ZXr-P Repeaters 4.3 Control Pushbuttons and Key Switch • The ZXr-A Repeater is equipped with five control keys for SOUND ALARMS, SILENCE / RESOUND, MUTE BUZZER, ACCEPT and System Sound Alarms SYSTEM RESET and a TEST key.

  • Page 13: Uzzer

    ZXr-A / ZXr-P Repeaters MORLEY-IAS • Examples of LCD during display test: |||||||||||||||||||||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||| ▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐ ▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐▐ ████████████████████████████████████████ ████████████████████████████████████████ • Example of LCD Test Display when Control Key pressed: ▐▐▐▐▐▐▐▐MMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMM MMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMM 4.4 Buzzer • The internal buzzer will sound to indicate alarm or fault conditions as follows: FIRE ALARM –...

  • Page 14: Specifications

    SILENCED, COMMUNICATIONS FAILURE and POWER. Push Buttons Control keys for RESET, MUTE BUZZER, ACCEPT, TEST, SOUND ALARMS and SILENCE / RESOUND. Buzzer Table 4 - ZXr-A / ZXr-P Repeaters Specifications Page 14 of 16 Document No. 996-144, Revision: 02, Operation & Installation Manual www.acornfiresecurity.com...
  • Page 15 ZXr-A / ZXr-P Repeaters MORLEY-IAS NOTES Operation & Installation Manual Document No. 996-144, Revision: 02, Page 15 of 16 www.acornfiresecurity.com...
  • Page 16 MORLEY-IAS ZXr-A / ZXr-P Repeaters © MORLEY-IAS. All rights reserved. ® The MORLEY-IAS Logo is a registered trademark. Page 16 of 16 Document No. 996-144, Revision: 02, Operation & Installation Manual www.acornfiresecurity.com...

This manual is also suitable for:

Zxr-p

Table of Contents