Table of Contents
Advertisement
Zhengzhou Audley Digital Control Equipments Co., Ltd
The manual for hot stamping machine of 330 explorer
This Manual Using:
1. Mainboard Version V4.23
2. Foil Control Center V2.4
3. Driver V6.3
4.Artcut date 12th April 2011
HH UUUhttp://www.ADL888.com
www.audley-printer.comUUUHHH
Tel:0086-371-55636896
0086-371-65638058
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Audley ADL-330B
- Page 1 Zhengzhou Audley Digital Control Equipments Co., Ltd The manual for hot stamping machine of 330 explorer This Manual Using: 1. Mainboard Version V4.23 2. Foil Control Center V2.4 3. Driver V6.3 4.Artcut date 12th April 2011 HH UUUhttp://www.ADL888.com www.audley-printer.comUUUHHH Tel:0086-371-55636896...
- Page 2 Port Repeat Speed Power Power (mm) (m/h) Source (kg) （kg） (mm) ADL-330B 0.5mm 50-80 AC220v 网络 U 盘 50/60HZ Check the equipment and verify spare part ㈠ Check the equipment whether there is exsit damage phenomenon ○ 1 Check the equipment bags whether are in good condition ②...
- Page 3 Printing head Gold foil keyboard plate nip roller Dust cover Power switch Put paper wearing Note：1.On the nip roller must keep clean, no dust, heavy article, water etc. 2.Try to put gold and not print medium keep on the middle of components. 3.
- Page 4 4. Under the print head have enough press power to harm your body, please don't put your hand under the print head. 5. Dust cover is to prevent dust, sundry etc fell to the print head and plastic roller, try not to tear down it.
- Page 5 "Width" is for the print length, "High" is for the print width, set "256 mm" and choice "horizontal". ②Choose "create new file". or click the right mouse button "text input" input to your content, for example ③Click You can according to need through the following tool bar set font properties ④The detailed set please refer to the artcut software's instructions or through the "file"...
- Page 6 Heating power: General according to the environment temperature and print material to adjust Temperature control: Keep acquiesce. It is better not more than 2%. Walking speed: The numeric is smaller and the speed of the print is faster, but the printing speed too fast will appear data loss phenomenon, generally not less than "15".
- Page 7 The method of stall print medium The install scheme of to be print medium The install scheme of gold foil Note: 1. When install cloth or gold foil, the cloth axis and the gold foil the flat a head of vertical shaft motor card into the slot, avoid to man-made destruct motor card slot.
- Page 8 ⑴Open the equipment power supply, the screen display interface as shown in figure, after about five seconds show the mainboard version information ⑵Operation panel System information Printed: Setting have been worked distance Remainder meters: Display the remainder distance can be printed out. (V3.22 versions are not support) Card number: Equipment motherboard number Machine type: Equipment type number...
- Page 9 Save carbon and delay: Adjust saving carbon with distance Set parameters Language: At present support simplified Chinese character, traditional Chinese character, English interface. According "V -" adjustment. Print correct: Generally as the default, such as print a 500mmX500mm color piece, print the actual size for 500mmX600mm, they can adjust the print correct numerical, if actual length is longer than goal length, increase the target print words correcting numerical, contrary to print decrease the value.
- Page 10 Recovery factory set: Press the "confirmation" button, it will be set back to the factory main board set. Format：Use for format SD card or U disk. Press test key under the file properties equipment will be automatically output shown below, the contents help you determine proper print parameters. Can switch over the storage devices.
- Page 11 Choose device after click ok, appears "control center". Parameter setting, coordinates movement and test keep default values, click "ribbon printing". All printing parameters setting is finished, choose ,choose documents you need to print in File management column , and click ok. ②offline print First click artcut toolbar Select the option "search".
- Page 12 ⑷ Setup parameters Heating power: Numerical according to material and working surroundings. General between 10 and 30.The bigger of numerical the better of peeling effect, but printing speed will slow. Exceed numerical will burn print medium even the print head. Temperature control: Current version does not support 3.01,keep default.
- Page 13 to SD card, you can choose "SD card". PC memory: Your equipment need not connect to Internet and computer when selecting this option. If you need to offline print put storage device connected to computers first. If your computer default your storage devices for G dish you can choose "G dish", click "ok"...
- Page 14 32 bit, please choose the 32 bit driver installation, 64-bit operating system please choose 64 a driver installation. First extract file "audley Setup," According to different computer systems, choose the "Printer Setup. Exe", in the popup dialog box selection. Input printer name, such as "330 A", select printer type "audley Ribbon"...
- Page 15 Set print task: Set print task according to following steps: 1) Choose a procedure compatible with Windows, for example Corel Draw, Microsoft Word, etc. 2) Determine print area. 3) Set page size. 4）Graphics and text place on the page. 5) Set print attribute. 6) Place printing materials on the print platform.
- Page 16 Input print images and text, such as after printed the image and edit, choose "print" Printer parameter Set...
- Page 17 printer name choose "330A ", and click "properties"...
- Page 18 Increase print speed may increase print strength. Tip: High print strength may cause gold foil adhesion in print head, please use Audley's gold foil paper, non Audley's gold foil paper may damage to print head.
- Page 19 Y side excursion: keep the default setting. Mode: Choose "drum" mode. Notice: Please stop print task at once when the gold foil paper is adhering to printer head, then clean the printer head. Reserve: Print task setting can reserve for next usage. Load: read-in pre-stored setting.
- Page 20 "Reduction of speed factor" keep default setting, others reference "stamping advanced options" setting. Press "reserve" after setting, and chose "browse and chose task" to modify task which reserved before. when chose this, also computer and product are both power on, equipment will link to net automatic.
- Page 21 IP address is obtain automatic. Advanced options of print parameter It is only for manufacturer adjusting, others adjusting will cause damage. Printer head temperature: Numerator means current printer head temperature, denominator means setting temperature; Printer head pressure: numerator means current printer head pressure, denominator means setting pressure;...
Need help?
Do you have a question about the ADL-330B and is the answer not in the manual?
Questions and answers