Download Print this page
Inel ST-01RN Series Instructions For Installation And Use

Inel ST-01RN Series Instructions For Installation And Use

Radio control flush mounted controller with integrated touch panel

Advertisement

Quick Links

Instruction for installation and use
1. SAFETY GUIDELINES
Basic guidelines
Before use read instruction for installation and use.
Check the compatibility of the permissible voltage of the device with the local power supply before
connecting.
Only qualified and licenced personnel is allowed to install and repair electrical devices.
It is prohibited to make any changes or modifications to the drive. Warranty repairs may be conducted only
by the manufacturer.
Use only original spare parts and accessories during post-warranty repairs.
Use an isolation switch allowing for safe power supply disconnection (e.g. fuse cut-off switch) installed in
such a way that all connections can easily be cut out.
Inspect wires and cables regularly for damaged insulation and conductor continuity.
If any damage is identified, cut off power immediately and replace the damaged wiring.
Supplementary safety regulations
When installing, using or carrying out maintenance work all binding health and safety regulations should be
followed. Particular attention should be paid to the following:
1. European Standards
2. Fire regulations
3. Accident avoidance regulations
PERSONAL SAFETY WARNING
Do not allow children to play with any of the control devices.
Keep all remote control devices out of the reach of children.
Observe the opening or shutting of the blinds, shutters, awnings or gates and ensure all persons stand clear
until the operation is completed.
Control system operators need to undergo preliminary instruction and training and also be made aware of all the
potential dangers that can be encountered. A person should only be authorised to use the control system only
once the employer, administrator or owner is satisfied that that person has been properly instructed.
It is not permitted to dispose of waste equipment together with other waste. Dispose only in specially
designated areas. The household plays a key role in the recycling of waste equipment. By correct sorting of
waste, including waste equipment and batteries, household members ensure that the equipment is not
disposed together with household waste, but in specially designated areas, and thus may be used again after recycling.
P.I.E. INEL Sp. z o.o.
ul. Mostowa 1
80-778 Gdańsk
ST-01RN
Radio control flush mounted controller with integrated touch panel
ST-01RN controller is compatible with RCUs:
PIL-01PT, PIL-01/04NS, PIL-01/05/09HT, PIL-01/05/09PM, PIL-19/99PMT,
PIL-01/05/09DL, PIL-19/99DLT.
Versions of ST-01RN:
ST-01RN – individual roller shutter controller
ST-01RNS – individual light controller
ST-01RNZ – individual venetian blinds controller.
inel@inel.gda.pl
biuro@inel.gda.pl

Advertisement

loading

Summary of Contents for Inel ST-01RN Series

  • Page 1 P.I.E. INEL Sp. z o.o. inel@inel.gda.pl ul. Mostowa 1 biuro@inel.gda.pl...
  • Page 2 Press the connected roller blind switch. • PIL-01/04NS, PIL-01/05/09/19PM, PIL-19/99PMT, PIL-01/05/09/19DL, PIL-19/99DLT Press ▲UP button for the channel to be registered on RCU. Blink of LED D2 will verify the correct registration. P.I.E. INEL Sp. z o.o. inel@inel.gda.pl ul. Mostowa 1 biuro@inel.gda.pl 80-778 Gdańsk...
  • Page 3 To clear all registered channels switch SW1 should be pressed and held until LED D2 starts to blink. After releasing the switch, all registered channels will be cleared. WARNING! There is no possibility to erase only one channel. P.I.E. INEL Sp. z o.o. inel@inel.gda.pl ul. Mostowa 1 biuro@inel.gda.pl...

This manual is also suitable for:

St-01rnSt-01rnsSt-01rnz