ClearSpan 105680 Manual

Screen house 12' wide

Hide thumbs

page of 33

/ 33
Bookmarks

Quick Links

Download this manual

is prohibited without permission.

Revision date: 12.19.07

ClearSpan

Screen House 12' Wide

Photo may show a different but similar model.

CLEARSPAN™ SCREEN HOUSE

™

STK#

105680

105681

105682

DIMENSIONS

12' W x 12' L

12' W x 18' L

12' W x 24' L

Need help?

Do you have a question about the 105680 and is the answer not in the manual?

Questions and answers

Summary of Contents for ClearSpan 105680

Page 1 CLEARSPAN™ SCREEN HOUSE ClearSpan ™ Screen House 12' Wide Photo may show a different but similar model. STK# DIMENSIONS 105680 12’ W x 12’ L ©2007 ClearSpan™ 105681 12’ W x 18’ L All Rights Reserved. Reproduction 105682 12’ W x 24’ L is prohibited without permission.
Page 2: Safety Precautions
• Never erect the structure under power lines. • Identify whether underground cables and pipes are Thank you for purchasing this ClearSpan™ shelter. When present before preparing the site or anchoring the properly assembled and maintained, this product will structure.
Page 3: Assembly Procedure
These words and phrases are common to most joints and to fasten brackets to rafters. ClearSpan™ shelters and identify the different parts of the shelter. (Some are used in this document. Others may not apply to this particular shelter.) These terms describe the shipped parts and can also be found on the materials list/spec sheets included with the shipment.
Page 4 CLEARSPAN™ SCREEN HOUSE REQUIRED TOOLS SQUARE THE SITE The following list identifies the main tools needed to 1. Identify a corner where a building rafter will be assemble the shelter. Additional tools and supports may be positioned, drive in a stake, and string a line the exact needed depending on the structure, location, and width of the building and stake in place.
Page 5 CLEARSPAN™ SCREEN HOUSE The following graphics and photos will help you identify the different parts and show you how they are used. (Not all parts are shown.) QH1400 FA4482B FAMF01B CC6212 Band Clamp Tek screw Fender Washer Fabric Clips Unswaged...
Page 6 CLEARSPAN™ SCREEN HOUSE ADDITIONAL PARTS IDENTIFICATION NOTES In some instances, there can be differences between the parts that are shown and referenced in the instructions and the parts that are shipped with the shelter. These differences do not affect the integrity of the shelter, but can change the assembly procedures.
Page 7 CLEARSPAN™ SCREEN HOUSE ClearSpan ™ Screen House ASSEMBLE THE MAIN ROOF FRAME This section is an overview of the process for assembling your roof frame assembly. See illustration below to identify main parts of the assembly. 1. Locate the required couplers and pipes and assemble the roof frame as shown below.
Page 8 CLEARSPAN™ SCREEN HOUSE ASSEMBLE THE LOWER FRAME This section is an overview of the process for assembling your lower frame assembly. See illustration below to identify main parts of the assembly. 1. Locate the required couplers and pipes and assemble the roof frame as shown below.
Page 9 CLEARSPAN™ SCREEN HOUSE 4. Rotate the square tube so that the Tek screws are to the inside of the shelter. ATTENTION: To prevent damage to the end panel and interference with the door installation, do not position the rail with the Tek screw heads to the top or front/ outside surface of the assembled tube.
Page 10 CLEARSPAN™ SCREEN HOUSE INSTALL END WALL FRAME ASSEMBLY: FRONT 9. Measure and mark the center of the end wall base rail. (CONTINUED) This mark will be used when you center the door in the end wall. 7. With the base rail secured between the end rafter legs, locate the two (2) remaining 16"...
Page 11 CLEARSPAN™ SCREEN HOUSE INSTALL END WALL FRAME ASSEMBLY: FRONT 17. Verify that the angled bracket (#QH1330) attached to (CONTINUED) the lower end of each frame tube is positioned to the outside of the door frame rough opening. 13. Take two (2) band clamps (#QH1400), remove the bolt and nut, and place the clamp over the upper tube of the end rafter.
Page 12 CLEARSPAN™ SCREEN HOUSE INSTALL END WALL FRAME ASSEMBLY: FRONT 26. Verify that the vertical door frame tubes are plumb and (CONTINUED) secure both pipe clamps to the end rafter. 21. Repeat the steps for the remaining vertical door frame 27. Recheck the rough door opening dimensions (top and tube.
Page 13 CLEARSPAN™ SCREEN HOUSE SQUARE THE ASSEMBLED FRAME Space below is reserved for customer notes. 1. With the frame in position, perform a final square of the frame by measuring diagonally (corner-to-corner) at the bottom of the legs and verify that the two measurements are equal.
Page 14 CLEARSPAN™ SCREEN HOUSE END PANEL INSTALLATION: FRONT 4. Take the base rail and insert it into the pocket of the end panel beginning at either of the outer cuts made in This procedure describes one way to install the end panel Step 2.
Page 15 CLEARSPAN™ SCREEN HOUSE END PANEL INSTALLATION: FRONT (CONTINUED) CUT THE DOOR OPENING: FRONT END PANEL The end panel material is cut and removed from the rough 7. Fold the edges around the rafter pipes and secure opening of the pedestrian door. These steps describe one the panel to the rafter pipes using fabric clips and Tek way to do this.
Page 16 CLEARSPAN™ SCREEN HOUSE INSTALL THE PEDESTRIAN DOOR 3. With the end panel secured to the left door frame tube, remove the header tube. Allow the brackets to remain The door for the shelter is installed between the vertical attached to the header tube.
Page 17 CLEARSPAN™ SCREEN HOUSE INSTALL THE PEDESTRIAN DOOR (CONTINUED) END PANEL INSTALLATION: BACK The end panel for the remaining end wall is installed and 6. With the door installed, swing the loose vertical door secured in the same manner as the previous end panel.
Page 18 CLEARSPAN™ SCREEN HOUSE END PANEL INSTALLATION: BACK (CONTINUED) 5. Slide each end of the end panel pipe into the remaining Space below is reserved for customer notes. opening of each 3-Way coupler located at the ends of the end rafter legs.
Page 19 CLEARSPAN™ SCREEN HOUSE RATCHET INSTALLATION 2. Move to the outside of the front end rafter and attach one (1) ratchet to the frame tube as shown in the The main cover is secured to the shelter frame using diagram that follows.
Page 20 CLEARSPAN™ SCREEN HOUSE MAIN COVER INSTALLATION NOTE: The black straps in the main cover are positioned at the front and back of the assembled The main cover is secured to the frame using ratchets and frame. straps. The straps are wrapped around a conduit inserted in a pocket along each side of the cover.
Page 21 CLEARSPAN™ SCREEN HOUSE MAIN COVER INSTALLATION (CONTINUED) 13. Thread the strap ends into the ratchet and slightly tighten. 9. Insert the straps from the main cover bonnet, into the ratchets attached to the end panel conduit. NOTE: It may be necessary to remove excess strap if it binds up in the ratchet.
Page 22 If the shelter is moved, inspect all parts and connections before reassembling. • For replacement or missing parts, call 1-800-245-9881 for assistance. NOTE: With the exception of Truss Arch buildings, ClearSpan™ shelters and greenhouses do not have any tested loading criteria. Revision date: 12.19.07...
Page 23 CLEARSPAN™ SCREEN HOUSE QUICK START GUIDE 12' Wide Screen House 12‛-0” Width FRONT Grid Represents 12” Squares 105680 (12' x 12') 105681 (12' x 18') 105682 (12' x 24') Revision date: 12.19.07...
Page 24 CLEARSPAN™ SCREEN HOUSE Revision date: 12.19.07...
Page 25 CLEARSPAN™ SCREEN HOUSE Revision date: 12.19.07...
Page 26 CLEARSPAN™ SCREEN HOUSE Revision date: 12.19.07...
Page 27 CLEARSPAN™ SCREEN HOUSE Revision date: 12.19.07...
Page 28 CLEARSPAN™ SCREEN HOUSE Revision date: 12.19.07...
Page 29 CLEARSPAN™ SCREEN HOUSE Revision date: 12.19.07...
Page 30 CLEARSPAN™ SCREEN HOUSE Revision date: 12.19.07...
Page 31 CLEARSPAN™ SCREEN HOUSE Revision date: 12.19.07...
Page 32 CLEARSPAN™ SCREEN HOUSE Revision date: 12.19.07...
Page 33 CLEARSPAN™ SCREEN HOUSE This page is reserved for customer notes. Revision date: 12.19.07...

This manual is also suitable for:

105681 105682