Amplifier Research  Manual

Amplifier Research Manual

Broadband microwave amplifier

Advertisement

®
Advanced Test Equipment Rentals
www.atecorp.com 800-404-ATEC (2832)
INSTRUCTIONS FOR SAFE OPERATION
BEFORE APPLYING POWER
Review this manual and become familiar with all safety markings and instructions.
Verify that the equipment line voltage selection is compatible with the main power source.
Protection provided by the equipment may be impaired if used in a manner not specified by Amplifier Research.
INTENDED PURPOSES
This equipment is intended for general laboratory use in a wide variety of industrial and scientific applications. It is
designed to be used in the process of generating, controlling and measuring high levels of electromagnetic Radio
Frequency (RF) energy. Therefore the output of the amplifier must be connected to an appropriate load such as an
antenna or field generating device. It is the responsibility of the user to assure that the device is operated in a
location which will control the radiated energy such that it will not cause injury and will not violate regulatory levels
of electromagnetic interference.
HAZARDOUS RF VOLTAGES
The RF voltages on the center pin of the RF output connector can be hazardous. The RF output connector should
be connected to a load before AC power is applied to the amplifier. Do not come into contact with the center pin
of the RF output connector or accessories connected to it. Place the equipment in a non-operating condition before
disconnecting or connecting the load to the RF output connector.
SAFETY GROUND
This equipment is provided with a protective earth terminal. The main power source to the equipment must supply
an uninterrupted safety ground of sufficient size to the input wiring terminals, power cord, or supplied power cord
set. The equipment MUST NOT BE USED if this protection is impaired.
PHYSICAL DAMAGE
The RF amplifier should not be operated if there is physical damage, missing hardware or missing panels.
MAINTENANCE CAUTION
Adjustment, maintenance, or repair of the equipment must be performed only by qualified personnel. Hazardous
energy may be present while protective covers are removed from the equipment even if disconnected from the
power source. Contact may result in personal injury. Replacement fuses are required to be of specific type and
current rating.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Amplifier Research and is the answer not in the manual?

Questions and answers

Summary of Contents for Amplifier Research Amplifier Research

  • Page 1 Review this manual and become familiar with all safety markings and instructions. Verify that the equipment line voltage selection is compatible with the main power source. Protection provided by the equipment may be impaired if used in a manner not specified by Amplifier Research. INTENDED PURPOSES This equipment is intended for general laboratory use in a wide variety of industrial and scientific applications.
  • Page 2 INSTRUCTIONS FOR SAFE OPERATION (continued) SAFETY SYMBOLS This symbol is marked on the equipment when it is necessary for the user to refer to the manual for important safety information. This symbol is indicated in the Table of Contents to assist in locating pertinent information.
  • Page 3: Table Of Contents

    Model 500T1G2 Manual Text TABLE OF CONTENTS SECTION I. Description and Specifications 1.1 TWTA Description ............1-1 1.2 Suggested Applications .............1-1 1.3 Specifications..............1-1 1.4 Accessories ..............1-2 1.5 Test Data Sheet ..............1-2 SECTION II. Theory of Operation 2.1 Design of the Amplifier ............2-1 2.2 Description of RF Circuit...........2-1 2.3 Description of Power Supply..........2-1 SECTION III.
  • Page 4 Model 500T1G2 Manual Text TABLE OF CONTENTS (Continued) ILLUSTRATIONS Figure 3-1 - Rear View of HPA..................3-3 Figure 3-2 - TWTA Front Panel Features..............3-5 Figure 3-3 - Front Panel Display Screens ..............3-7 Figure 3-4 - TWTA Rear Panel Features..............3-11 TABLES Table 1 - Front Panel Features ..................3-5 Table 2 - Rear Panel Features ...................3-11 Table 3 - Catalog of IEEE-488 Commands ...............3-13 Table 4 - Catalog of Status Codes................3-16...
  • Page 5: Description And Specifications

    Antenna and component testing Equipment calibration General laboratory instrumentation PECIFICATIONS Refer to the Amplifier Research Data Sheet on the following pages for detailed specifications. CCESSORIES Amplifier Research offers a number of accessories for use with this amplifier including: • Directional coupler •...
  • Page 6: Test Data Sheet

    Model 500T1G2 Manual Text HEET A Test Data Sheet for a specific unit is prepared at the time of manufacture and is included with the unit's copy of this manual. REV A...
  • Page 7: Theory Of Operation

    Model 500T1G2 Manual Text SECTION II THEORY OF OPERATION ESIGN OF THE AMPLIFIER The model 500T1G2 TWT amplifier consists of four principal subsystems. Two of these subsystems, the microwave power assembly (A27680) and the TWT power supply (A27825) are discussed in sections 2.2 and 2.3, respectively.
  • Page 8: Description Of Power Supply

    Model 500T1G2 Manual Text RF C (continued) ESCRIPTION OF THE IRCUIT Amplifier gain is determined by the variable attenuator which has a voltage-controlled loss. Gain adjustment is made by front panel control or over the remote interface. In either case, the control head sets the output of a digital-to-analog converter (DAC) on the HPA interface board.
  • Page 9: Operation

    Model 500T1G2 Manual Text SECTION III OPERATION ARNINGS AND AUTIONS Throughout this manual, the symbol ARNING indicates that a hazard exists that may result in personal injury or loss of life. The symbol AUTION indicates that failure to follow procedures may result in damage to the equipment. ANGER OLTAGE RESENT...
  • Page 10 Model 500T1G2 Manual Text Save and store the shipping container in case the unit needs to be returned in the future for calibration or repair. REV A...
  • Page 11: Mounting

    If rack mounting of models provided with lifting handles is desired, one or more of the lifting handles may need to be removed to clear the rack’s front mounting rails. Optional slide rails for rack mounting are available from Amplifier Research. NOTE: D...
  • Page 12: 3.2.3 Cooling Requirements

    Model 500T1G2 Manual Text 3.2.3 Cooling Requirements The TWTA is provided with cooling fans. It is important that air movement around the rear of the unit be unobstructed. AUTION TWTA OR EITHER BENCH OR RACK MOUNTING DO NOT POSITION THE IN SUCH A WAY THAT THE AIR INTAKE OR OUTLET ARE BLOCKED OR THAT THE EXHAUST FLOW IS DIRECTED INTO THE...
  • Page 13: 3.2.6 External Interlock Connector

    Model 500T1G2 Manual Text 3.2.5 RF Output Connections (continued) If an external isolator is installed at the output of the TWTA, either the i s olator should have a load capable of dissipating the full output of the TWTA or the isolator load should be provided with a temperature sensing switch.
  • Page 14: Front Panel Features

    Model 500T1G2 Manual Text RONT ANEL EATURES EFER TO IGURE BELOW Model 500T1G2 500 Watts 1.0 - 2.5 GHz INHIBIT LOCAL STANDBY OPERATE REMOTE EXIT MAIN POWER Figure 3-2 Front Panel Features ABLE RONT ANEL EATURES Item Title Function MAIN POWER Switchable 15 A.
  • Page 15: Front Panel Display And Soft Keys

    Model 500T1G2 Manual Text RONT ANEL ISPLAY AND The purpose of the front panel display is to permit the operator to access extensive information about the condition and operation of the TWTA. To accomplish this, a number of informational screens are programmed.
  • Page 16 Model 500T1G2 Manual Text (continued) RONT ANEL ISPLAY AND Menu screens - The screens at the highest level are called menu screens. There are four menu screens. At power on, the MENU 1 screen is displayed. Each of the menu screens has the soft key S4 labeled MORE.
  • Page 17 Model 500T1G2 Manual Text (continued) RONT ANEL ISPLAY AND Pressing more brings up WARNINGS 2, which allows the under forward power setpoint to be entered. Adjusting this to the minimum value causes -OFF- to be selected, disabling this alarm. In WARNINGS 3, the maximum reflected power level is set. Note that these are warning levels at which the beep sounds;...
  • Page 18 Model 500T1G2 Manual Text CU line voltage too low to operate. System shutdown (continued) RONT ANEL ISPLAY AND In the event that one of these appears, shut off the TWTA and contact an authorized service representative before proceeding. AUTION TWTA TTEMPTS TO OPERATE THE DESPITE CONTROL UNIT PROBLEMS MAY RESULT IN LOSS OF THE STATIC...
  • Page 19: Rear Panel Features

    Model 500T1G2 Manual Text ANEL EATURES IGURE BELOW RF OUTPUT REMOTE A2J2 INTERFACE FORWARD SAMPLE OUT IEEE-488 TYPE N -50 dB (NOM) EXTERNAL INTERLOCK SAFETY A2J1 GROUND RF IN 0 dBM MAX AC IN 208VAC 60 HZ 3 P H 3 KVA Figure 3-4 Rear panel Features...
  • Page 20: Initial Turn-On And Warm-Up Procedure

    Model 500T1G2 Manual Text NITIAL N AND ROCEDURE Install the TWTA as discussed in section 3.2 Provide an RF generator to the RF input Type N connector A1J1. Set RF generator level below -50 dBm and set desired frequency in specified range. Connect a load suitable for 1000 watts continuous operation to the output 7-16 DIN connector.
  • Page 21: Emergency Bypass Operation

    Model 500T1G2 Manual Text MERGENCY YPASS PERATION For reference, see schematic 10-24830 in section 5.2. The TWTA is provided with a means of operating the amplifier manually in the event that there is a failure of the control module and it is imperative that the amplifier remain on line. AUTION MERGENCY BYPASS OPERATION DISABLES ALL MICROPROCESSOR BASED INTERACTIVE FEATURES AND POSSIBLY SOME DIAGNOSTIC FEATURES...
  • Page 22 Model 500T1G2 Manual Text IEEE-488 O (continued) EMOTE PERATION ABLE IEEE-488 C ATALOG OF OMMANDS Command Function Units Response format RDSTAT Returns status code of processing of previous STATUS=[ ] command (see Table 4) RDFLT Returns system fault code (see Table 5) flt=[ ] OPERATE;...
  • Page 23 Model 500T1G2 Manual Text IEEE-488 O (continued) EMOTE PERATION ABLE IEEE-488 C (continued) ATALOG OF OMMANDS SPOHID Sets over forward power warning setpoint (dBm) RDPOLOD Returns under forward power warning setpoint Polo=[ ]dBm (dBm) SPOLOD Sets under forward power warning setpoint (dBm) RDPOHIW Returns over forward power warning setpoint (W) watts...
  • Page 24 Model 500T1G2 Manual Text IEEE-488 O (continued) EMOTE PERATION ABLE RDFLT C ATALOG OF AULT ODES ETURNED BY OMMAND (The RDFLT command causes the TWTA to return a string in the form flt=[code], where [code] is an ACSII number whose meaning is given below). Fault Code Meaning No fault...
  • Page 25: Remote Ieee-488 Operation

    Model 500T1G2 Manual Text IEEE-488 O (continued) EMOTE PERATION ABLE ATALOG OF YSTEM TATE ODES (The RDLOGIC command causes the TWTA to return a string in the form Sys=[code], where [code] consists of 2 bytes encoded as follows) Meaning if high 0 (LSB) High voltage on Transmit on...
  • Page 26 Model 500T1G2 Manual Text IEEE-488 O (continued) EMOTE PERATION ABLE *STB?; R ESPONSE ODES (The command *STB?; causes the TWTA to send a string containing an operational state code consisting of 2 ASCII characters representing hex digits. The response is in the form “STATUS:[x][y][eol] ” where the hex values of [x] and [y] are formed as shown below) x bit Meaning...
  • Page 27: Twta General Considerations

    Model 500T1G2 Manual Text and displaying/monitoring the Status Codes. Consult the application program users instructions for Remote Operation procedure. IEEE-488 O (continued) EMOTE PERATION The following recommendations are provided to guide the software developer in writing host software for the TWTA: The TWTA does not send SRQ (service request).
  • Page 28 25 times, until the Operate mode is actually set. If this condition persists, contact Amplifier Research Service for additional assistance. (See Explanation of…, below) Noise Power Density (NPD): TWTAs produce rf noise over their operating frequency range, as specified by the Noise Power Density (NPD).
  • Page 29 Model 500T1G2 Manual Text To preclude this gassing problem, and thus reduce the need for repeating the “Operate” selection, it is recommended that the time in “Standby” be limited – to about one hour. Extended periods in “Standby” may result in an inability to clear the fault by this method. In this case, service measures may be needed to correct the unit.
  • Page 30: Maintenance

    Model 500T1G2 Manual Text SECTION IV MAINTENANCE The TWTA has minimal maintenance requirements. The only moving parts are the elements of switches, relays and the fans. Preventive maintenance recommendations are found in Paragraph 4.3. Most repairs to the TWTA should be performed by the factory. However, some user service organizations may choose to make feasible repairs in-house.
  • Page 31: Preventive Maintenance

    Model 500T1G2 Manual Text (continued) REVENTIVE AINTENANCE Disconnect power, RF, and any other interface connectors. On the rear of the unit, remove any screws used to connect brackets to the amplifier. On the front of the unit, remove the four screws holding the front panel onto the cabinet.
  • Page 32: Non-Repairable Modules

    Model 500T1G2 Manual Text (continued) ROUBLESHOOTING After review of the symptoms of the failure, the user may want to check for a loose connector or component especially after rough handling of the unit. Look externally for physical damage and internally for unmated or loose parts.
  • Page 33: Technical Documentation

    Model 500T1G2 Manual Text SECTION V TECHNICAL DOCUMENTATION - Note - The purpose of this technical documentation section is to provide a guide to the TWTA for technician-level servicing. It is intended for use by qualified technical personnel who must troubleshoot and repair the TWTA in the field.
  • Page 34: Top Level Build Tree

    Model 500T1G2 Manual Text EVEL UILD BUILD TREE FOR SERIAL NUMBER 500 W L-BAND TWTA A26900-313 A26900-313 500 W L-BAND TWTA A27825-000 3KW 5KV POWER SUPPLY FOR 500L 1A1A1 A27824-000 HI,HEATER POWER SUPPLY 1A1A1T1 A09553-000 XFMR,HEATER FEEDBACK 1A1A1L1 A09594-900 MODIFIED INDUCTOR 1A1A1L2 A09595-900 MODIFIED INDUCTOR 1A1A1T2...
  • Page 35 Model 500T1G2 Manual Text REV A...
  • Page 36: Schematics

    Model 500T1G2 Manual Text CHEMATICS HPA LOGIC & CONTROL ASSY 10-A23050 EMERGENCY BYPASS BOARD 10-A24830 HPA INTERFACE BOARD 10-A25444 500 W L-BAND TWTA 10-A26900 REV A...
  • Page 37: Wiring Diagram

    Model 500T1G2 Manual Text IRING IAGRAMS POWER SUPPLY FOR TWT 5196 20-A27825 REV A...
  • Page 38: Parts Lists

    Model 500T1G2 Manual Text ARTS ISTS HPA LOGIC EMERGENCY & CONTROL ASSY 61-A23050-000-C BYPASS BOARD 61-A24830-001-A HPA INTERFACE BOARD 61-A25444-000-A 500 W L-BAND TWTA 31-A26900-313-A MICROWAVE POWER ASSEMBLY (L-BAND) 31-A27680-000-D 500 L-BAND WIRING KIT 31-A27682-000-C 3 KW 5 KV POWER SUPPLY FOR 500 L 31-A27825-000-C REV A...
  • Page 39: Recommended Spare Parts

    Model 500T1G2 Manual Text ECOMMENDED PARE ARTS A23692-000 400H INVERTER 1 EA A16495-000 LOW VOLTAGE POWER SUPPLY MODULE 1 EA A23050-000 HPA LOGIC AND CONTROL MODULE 1 EA A23065-000 INPUT FILTER MODULE 1 EA A27815-000 POWER INVERTER MODULE 1 EA A27818-000 TANK MODULE 1 EA A27821-000 5 KV 3 KW HV FILTER...
  • Page 40: Sample Program For Ieee-488 Communication

    Model 500T1G2 Manual Text Sample Program for IEEE-488 Communication 1000 ! *********************************************** 1010 IEEE-488 COMMUNICATIONS SOFTWARE 1030 7/24/92 AARON D. McCLURE 1040 ! *********************************************** 1041 DIM F$[80] 1042 DIM A$[80] 1050 CLEAR SCREEN 1060 INPUT "INPUT COMMAND TO SEND TO POWER SUPPLY. EXIT TO QUIT.",A$ 1070 IF A$="EXIT"...
  • Page 41 HPA LOGIC AND CONTROL MODULE 61-A23050-000-C Model Number HPA Last Rev 11/04/97 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- REV B B23050-000 LOGIC & CONTROL BOARD 1 EA 8M906 C48,C49 C06103-000 CAP,10MF,25V,20%,SOLID 2 EA TANT,RADIAL,(AVX TAP106M025HSB) C16333-000 CAP,33MF,25V,AERL, 1 EA (NICHICON UVX1E330M)
  • Page 42 ARI SHRAGER PAGE 11/04/97...
  • Page 43 HPA LOGIC AND CONTROL MODULE 61-A23050-000-C Model Number HPA Last Rev 11/04/97 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- R1,R9,R19,R37, R00100-000 RES,10 OHM,1/4W,5%,CC,(A/B 6 EA R44,R50 RC07GF100J) R4,R20,R27,R29 R01100-000 RES,100 OHM,1/4W,5%,CC, 4 EA (A/B RC07GF101J) R01820-000 RES,820 OHM,1/4W,5%,CC, 1 EA (A/B RC07GF821J) R5,R7,R17,R18,...
  • Page 44 PAGE...
  • Page 45 HPA LOGIC AND CONTROL MODULE 61-A23050-000-C Model Number HPA Last Rev 11/04/97 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- R32004-000 TRIMPOT,1K,1/2W,10%,CERMET, 1 EA 20T,SIDE ADJ,(BECKMAN 67X) R10,R12,R15,R16 R32020-000 TRIMPOT,10K,1/2W,10%, 4 EA CERMET,20T,SIDE ADJ, (BECKMAN 67X) R13,R14 R32049-000 TRIMPOT,5K,1/2W,10%,CERMET, 2 EA 20T,SIDE ADJ,(BECKMAN 67X)
  • Page 46 PAGE...
  • Page 47 EMERGENCY BYPASS BOARD 61-A24830-001-A Model Number 20T Last Rev 11/06/96 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- REV C B24830-000 EMERGENCY BYPASS BOARD 1 EA 8M906 C3-C5 C04105-000 CAP,0.1MF,100V,20%,POLY 3 EA FILM,RADIAL,OIL,[KEMET C331C104M1R5CA] C31028-000 CAP,1000PF,200VDC,10%,CER, 1 EA 1% FAILURE,(KEMET CKR05 SERIES) C31032-000 CAP,0.01MF,200VDC,10%,CER,...
  • Page 48 MAARTEN KORRINGA PAGE 11/06/96...
  • Page 49 EMERGENCY BYPASS BOARD 61-A24830-001-A Model Number 20T Last Rev 11/06/96 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- R20267-000 RES,267 OHM,1/2W,1%,MF, 1 EA 100PPM,(DALE RN55D) R10,R11,R12 R23100-000 RES,100K,1/2W,1%,MF,100PPM, 3 EA (DALE RN55D) R30074-000 TRIMPOT,1K,1/2W,10%,CERMET, 1 EA 100PPM,20T,TOP ADJ, (BECKMAN 66W) S2,S3 S22004-000 SWITCH,TOGGLE,DPDT,PC MNT,...
  • Page 50 PAGE...
  • Page 51 HPA INTERFACE BOARD 61-A25444-000-A Last Rev 03/28/97 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- REV. B B25444-000 8M906 C6,C7,C9,C13, C01104-000 CAP,100PF,50V,CER,(R.G. 8 EA C16,C39,C43,C69 ALLEN C1C101J1HS2L) C02109-000 CAP,1000PF,1KV,CER,(RG 1 EA ALLEN C11B102K3AS6L) C1-5,C10,C11, C04105-000 CAP,0.1MF,100V,20%,POLY 62 EA C22-26,C28,C30, FILM,RADIAL,OIL,[KEMET C33,C35,40-42,...
  • Page 52 MAARTEN KORRINGA PAGE 03/28/97...
  • Page 53 HPA INTERFACE BOARD 61-A25444-000-A Last Rev 03/28/97 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- I10074-000 LED,GREEN,ALGAAS, 1 EA NON-DIFFUSED,(HEWLETT PACKARD HLMP-1540) J10021-000 RIGHT ANGLE HEADER,2 PIN 1 EA SERIES 7478,(MOLEX 22-05-3021) J10371-000 CONN,37 PIN VERTICAL,MALE, 1 EA P.C.B.
  • Page 54 PAGE...
  • Page 55 HPA INTERFACE BOARD 61-A25444-000-A Last Rev 03/28/97 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- R20243-000 RES,243 OHM,1/2W,1%,MF, 1 EA 100PPM,(DALE RN55D) R20845-000 RES,845 OHM,1/2W,1%,MF, 1 EA 100PPM,(DALE RN55D) R3,R5 R30071-000 TRIMPOT,10K,1/2W,10%, 2 EA CERMET,100PPM,20T,TOP ADJ, (BECKMAN 67W) R9,R10,R12,R15, R30103-000 RES,10K,1/8W,1%,MF,100PPM, 11 EA R22,R30,R35,...
  • Page 56 PAGE...
  • Page 57 HPA INTERFACE BOARD 61-A25444-000-A Last Rev 03/28/97 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- U6,U19,U34,U39 U20148-000 IC,HEX INVERTER,SCHMIDTT 4 EA TRIGGER,(74HC14) (SSD) U20730-000 IC,DUAL J-K FLIP FLOP 1 EA W/RESET,(7473) (SSD) U21328-000 IC,QUAD 2 INPUT NAND, 1 EA SCHMIDTT TRIGGER,(74HC132) (SSD)
  • Page 58 PAGE...
  • Page 59 HPA INTERFACE BOARD 61-A25444-000-A Last Rev 03/28/97 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- NOTES: Install the four D-sub connectors (J1-J4) with 4-40 hardware prior to soldering. Install spring latches J31014 on J1-J4. Install dead lead in R33, R34. Apply conformal coating-after QC.
  • Page 60 PAGE...
  • Page 61 500 W L-BAND TWTA 31-A26900-313-D Last Rev 02/20/98 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- A6,A7 A16483-000 400H INVERTER 2 EA 8M906 A25444-000 HPA INTERFACE BOARD 1 EA 8M906 A26856-000 HPA SYSTEM CONTROL FRONT 1 EA 8M906 PANEL ASSY AR 500T A27509-300 HPA CONTROL CHASSIS ASSY,...
  • Page 62 MAARTEN KORRINGA PAGE 02/20/98...
  • Page 63 MICROWAVE POWER ASSEMBLY (L-BAND) 31-A27680-000-D Last Rev 02/20/98 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- E01009-000 HIGH POWER COAXIAL CABLE, 1 EA 14.1" LONG, SC-SP/N-SP, [MALIK CABLE DEVICES N. A. -SCPS] E08032-000 TWT,1-2.5 GHZ,CW,535 W,TWT 1 EA ASSY (TELEDYNE MEC-5203) E20192-000 DUAL HIGH POWER, 1 EA...
  • Page 64 MAARTEN KORRINGA PAGE 02/20/98...
  • Page 65 500 L-BAND WIRING KIT 31-A27682-000-C Last Rev 02/20/98 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- E10011-000 THREE PHASE PI FILTER,15A, 1 EA LOW PROFILE,FLANGE MT, (FILTER CONCEPTS 3L15LF) H10066-000 CABLE TIE MOUNT #8 SCREW 25 EA (PANDUIT TA1S8-C) H10067-000 FLAT CABLE MOUNT,2"WIDE 2 EA...
  • Page 66 MAARTEN KORRINGA PAGE 02/20/98...
  • Page 67 500 L-BAND WIRING KIT 31-A27682-000-C Last Rev 02/20/98 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- J12052-000 CONN,TYPE D RECT,5S,HI 1 EA POWER J12091-000 CONN,D-SUBMINIATURE,9 PIN, 2 EA FEM,(ITT CANNON DEU-9S) J12250-000 CONN,PLUG,D-SUB,25-PIN,FEM, 1 EA CRIMP (DBU-25S) J17250-000 BULKHEAD MT N-JACK TO SMA 3 EA JACK ADAPTOR,(OMNI-SPECTRA...
  • Page 68 PAGE...
  • Page 69 500 L-BAND WIRING KIT 31-A27682-000-C Last Rev 02/20/98 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- W01880-000 WIRE,26 AWG,COAXIAL, 4 FT RG-188A/U,900V (BELDEN 83269) W11400-000 WIRE,14AWG,BLUE,(ALPHA 4 FT 5859) W11600-000 WIRE,16AWG,BLUE,(BELDEN 2 FT 83010) W11800-000 WIRE,18AWG,BLUE,(BELDEN 3 FT 83009) W12000-000 WIRE,20AWG,BLUE,(BELDEN 4 FT...
  • Page 70 PAGE...
  • Page 71 3KW 5KV POWER SUPPLY FOR 500L 31-A27825-000-A Model Number 500L Last Rev 02/05/98 Control# CORRECTION REF. DESIG. ETM P/N DESCRIPTION QTY U/M CAGE ----------------------------------------------------------------------- A16495-000 LOW VOLTAGE POWER SUPPLY 1 EA 8M906 MODULE A23050-000 HPA LOGIC AND CONTROL 1 EA 8M906 MODULE A23065-000 INPUT FILTER MODULE...
  • Page 72 VICTOR ENG PAGE 02/05/98...

Table of Contents

Save PDF