Vacuum Cleaning; Maintaining The Appliance - Dirt Devil REBEL34 Instruction Manual

NOTE:
You can also use the suction nozzles without the
telescopic tube as necessary. To do so, connect
the required accessories directly to the handle
(Fig. 9 ).
Connect the required accessory to the handle or
1
the telescopic tube (Fig.
accessory is securely connected. ➔ The appliance
can be connected.
Connecting the appliance
CAUTION!
If the red marking is visible (Fig.
the connection cord by pressing the cord rewind
button to pull in the cord up to the yellow mark
(Fig. 6 / ) (Fig. 7 ). Otherwise, the connection
2
cord might be damaged.
Pull the cable out of the appliance (Fig.
1
Insert the plug into a mains socket.
2

Vacuum cleaning

Flexible vacuum-cleaning
Connect the required accessories >"Using the ac-
1
cessories" on page 16.
2
>"Connecting the appliance" on page 18.
on the appliance, press the ON/OFF button (Fig.
➔ The appliance vacuums at full suction power.
To reduce the suction power, open the bypass
4
vent as required >"Regulating the suction power"
on page 17. To switch off the appliance, press
5
the ON/OFF button again (Fig.
switches off. Close the bypass vent (Fig.
6
that the appliance operates with full suction power
when vacuum-cleaning the next time.
Regulating the suction power
To reduce the suction power, slide the bypass vent
1
open (Fig. 11 ). To increase the suction power, slide
2
the bypass vent closed again (Fig.
Storing the appliance
NOTE:
If necessary, use the holding clip on the suction
hose (Fig. / ) to attach accessories.
1
12
Switch off the appliance and pull the plug from the
1
socket. Push the cord rewind button (Fig.
2
until the cord has been fully rewound (Fig.
). Make sure that the
9
2
/ ), retract
6
1
).
5
Connect the appliance
To switch
3
8
). ➔ The appliance
8
/ ) so
1
14
).
11
/
1
7
).
7
EN
Hang the telescopic floor nozzle or parquet nozzle
3
(connected to the telescopic tube or handle) in the
parking bracket (Fig.

Maintaining the appliance

Emptying the dust bin
Switch off the appliance and pull the plug from
1
the socket. Press the dust bin release catch
2
(Fig. / ) and remove the dust bin from its console
1
6
in the appliance (Fig.
above a waste bin and release the dust bin (Fig.
Dispose of the contents of the dust bin in a waste
4
bin. Gently tap out the dust bin to remove any soil-
ing. Close the emptied dust bin.
5
dust bin into its console in the appliance so that you
feel it click into place.
Cleaning the separator and filter
NOTE:
The appliance, the separator and the pre-motor
filter should be cleaned regularly in order to
maintain the suction power. Empty and clean the
dust bin at the latest when the cleaning/empty-
ing display lights up (Fig.
Remove the dust bin from the appliance, >"Emp-
1
tying the dust bin" on page 18.
dust bin cover release (Fig.
pre-motor filter (Fig.
together with the separator cover, from the dust bin
).
(Fig. ). Release the separator cover (Fig.
16
5
Remove the cover from the separator (Fig.
6
Remove the separator and dispose of the con-
7
tent in a waste bin.
the separator out thoroughly under running water.
Leave the cleaned parts to dry completely for at
9
least 24 h. Insert the separator cover into the sep-
10
arator (Fig. ).
19
11
the separator cover, into the dust bin (Fig.
Place the pre-motor filter on the dust bin (Fig.
Close the dust bin cover.
13
into its console on the appliance body. You must be
able to feel the dust bin click into place.
)
/ ) (Fig. ).
1 12
8
). Place dust bin closely
13
3
Re-insert the
6
).
13
Push the upper
2
/ ). Remove the
1
1 3
15 ). Remove the separator,
4
Rinse the pre-motor filter and
8
Insert the separator, together with
20
Re-insert the dust bin
14
17
14 ).
).
17
).
18
).
12
).
21