Advertisement
Quick Links
O P E R A T O R ' S M A N U A L
For Models 350 & 210
Model 210
Model 350
WAR N IN G
Re a d a nd b ecome f amilia r wit h t his m an ua l BEFO RE op erating u n it.
Before operating this equipment, thoroughly read this set of instructions, make sure you
understand them, and only then follow the step-by-step directions . Failure to do so could
result in serious property damage and / or serious bodily injury .
Drawings and photos are for illustrative purposes only . Due to the nature of ongoing product development
and improvement, actual product component confi gurations may vary somewhat from images in this manual.
Form M042-50-00-00 version 3
© 2019 Paragon Pro Manufacturing Solutions All Rights Reserved.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Paragon Pro Telpro Drillrite 350
Summary of Contents for Paragon Pro Telpro Drillrite 350
- Page 1 Drawings and photos are for illustrative purposes only . Due to the nature of ongoing product development and improvement, actual product component confi gurations may vary somewhat from images in this manual. Form M042-50-00-00 version 3 © 2019 Paragon Pro Manufacturing Solutions All Rights Reserved.
- Page 2 To our valued customer, Thank you for choosing a product by Paragon Pro Manufacturing Solutions. We are pleased that we are able to provide equipment to make your work easier. Our efforts are focused on producing the finest quality equipment of which we are capable. We make sure to spend extra time and effort on our design and production in order to reduce your time and effort spent using the product.
- Page 3 CONTENTS Warning / Instructional Information User . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1 Page 2 Components .
- Page 4 . Failure to do so could result in electrocution . • Use caution to keep power cords clear of moving parts during operation . Questions? - Call Paragon Pro Manufacturing Solutions Customer Service at 1-800-448-0822 or 701-775-0551 - 1 -...
-
Page 5: User Components
USER COMPONENTS Model 350 A. Base Assembly E. Safety Remote Switch Cable Assembly B. Frame Assembly F. Vacuum Hose C. Drill Cradle Assembly Tool Rest G. Tool Tray D. Drill Cradle Assembly with Dust Extraction Model 210 A. Dolly Base Assembly D. -
Page 6: Care And Maintenance
CARE AND MAINTENANCE • Occasionally oil the caster bearings, thumb screws and pull pins for smooth operation . • Keep the chain lightly lubricated and do not expose it to moisture . Be careful not to over oil, as excess drip oil may cause grit to accumulate between moving parts . •... - Page 7 FITTING THE CRADLE TO YOUR DRILL Key Part Function Slide/Tilt Bar Holds the handle of the drill and aligns the drill with the DrillRite™ Frame . Adjust the (Two are provided . Select the one which Vacuum Port to best fi ts the drill to be mounted.) Approximately Slide/Tilt Bar Lock Locks the Slide/Tilt Bar in place .
- Page 8 ASSEMBLY 3 . (Model 350) Install the cable guide for drill trigger activator cable 1 . Swing the base Brake Bar down as shown then install the Frame Assembly into the Base Assembly . Orient the frame handle forward toward the base Brake Bar as shown . Tighten all four thumb screws evenly to secure the Frame Assembly into the Base Assembly .
- Page 9 ASSEMBLY 5 . Install the cable operated trigger activator assembly fully into the Support Mount and tighten lock bolt “A” above . 6 . Install the Trigger Handle assembly into the mount on the frame and secure with the lock pin . NOTE: Follow these steps for initial set up of the trigger acti- 7 .
-
Page 10: Operation
PARTS INDEX Model 350 OPERATION NOTE: • After initial assembly, adjustments and fi tting of the DrillRite™ Overhead Concrete Drill Press to your drill, it is recommended that the drill remains mounted in the cradle for more rapid assembly and disassembly of the equipment when moving from job to job . - Page 11 This product contains trace amounts of the following items which are known to cause cancer and/or developmental harm in the state of California. These chemicals are not hazardous under product's intended use. Please review CAS# for more information. Chemical Hazard CAS# % By Weight Arsenic...
- Page 15 For Parts and Service Contact: Paragon Pro Manufacturing Solutions 1-800-448-0822 1-701-775-0551 sales@paragonpromfg.com Form M042-50-00-00 version 3...
- Page 16 Questions about assembly? Can’t find a part? Need some other help? Call us: 1.800.448.0822 701.775.0551 We’ll get you set up!
Need help?
Do you have a question about the Telpro Drillrite 350 and is the answer not in the manual?
Questions and answers