Advertisement
Quick Links
Introduction
Purpose
This manual provides instructions for installing the Encore
for all Encore units (standard and S series).
Table of Contents
Topic
Introduction
Important Safety Information
Before You Begin
Installing Encore Canopy Light Kit
Required Tools and Materials
Following tools and materials are required for the kit installation:
• Impact Tool with an M13 Socket
• M17 Socket
• Metal Punch
• Pliers (Channellock
• Hammer
Parts List
Following table lists the parts included in the Encore Canopy Light Kit:
Item
1
MDE-4327B Encore® Canopy Light Kit (M03225K001) Installation Instructions · October 2015
Page
)
®
Description
Assembly, Canopy Light, Encore
• Bracket, Encore Canopy Light
• Cable-tie
• Assembly, Canopy Light Nipple and Wire
• Elbow, Conduit 1/2 NPT 90
• Nipple, Conduit 1/2x2-3/4
• Conduit, Encore Canopy Light
• Nut, Hexagonal Flanged Serrated Locking Face, 1/4"-20
• Nut, Conduit 1/2"
• Power Line, Unilet
®
• Screw, Metric, Thread Forming, Hexagonal-head Washer and Pozidrive
Pan-head, M8 X 18
• U-bolt, 1/4"-20 X 1.5
• Washer, Flat .875 X 1.62 X .056
Encore
Canopy Light Kit (M03225K001)
®
1
3
5
7
Installation Instructions
October 2015
®
Canopy Light Kit (M03225K001)
Part Number
M08543A001
M03205B003
Q10178-01
R19101-G2
K42428
R11976-23
M08543B001
Q11890-04
K89681
K72943
M00417B009
K67996-02
N16599-59
MDE-4327B
Quantity
1
1
2
1
2
1
1
2
2
1
1
1
2
Page 1
Advertisement
Related Manuals for Gilbarco Encore
Summary of Contents for Gilbarco Encore
- Page 1 • Impact Tool with an M13 Socket • M17 Socket • Metal Punch • Pliers (Channellock ® • Hammer Parts List Following table lists the parts included in the Encore Canopy Light Kit: Item Description Part Number Quantity Assembly, Canopy Light, Encore M08543A001 •...
- Page 2 M12630B001 Bracket, Canopy Light Conduit, Encore M14407A001 Encore Canopy Light Kit contains three brackets to mount the canopy to the lower frame. Refer to the following table to find the appropriate bracket based on the lower frame manufactured date: Brackets...
- Page 3 • Use of safety tape, cones, or barricades at the affected unit(s) DEF is non-flammable. Therefore, explosion and fire safety • A total electrical shut-off of the affected unit(s) warnings do not apply to DEF lines. MDE-4327B Encore® Canopy Light Kit (M03225K001) Installation Instructions · October 2015 Page 3...
- Page 4 Subpart S of 29 CFR Part 1910 - Electrical Hazards, 29 CFR Part 1910.333 contains specific Lockout/Tagout provision for electrical hazards. Page 4 MDE-4327B Encore® Canopy Light Kit (M03225K001) Installation Instructions · October 2015...
- Page 5 Before You Begin Before You Begin Read and understand all safety information and test procedures found in MDE-3804 Encore and Eclipse Start-up/Service Manual. CAUTION A properly grounded Electrostatic Discharge (ESD) wrist strap must be worn while servicing any electronic devices or components. Failure to use electrostatic precautions may damage electronic components and void warranty.
- Page 6 • Use system circuit breakers. • Multiple disconnects may be required. Follow OSHA lockout/tagout procedures as described in MDE-3804 Encore and Eclipse Series Start-up/Service Manual. Place the nozzle in an approved container and squeeze the lever to release pressure with the nozzle hook in the OFF position.
- Page 7 Right J-box Side 1 Lower Panel Place all the external/cosmetic sheet metal that has been removed in a safe place to prevent damage during the kit installation. MDE-4327B Encore® Canopy Light Kit (M03225K001) Installation Instructions · October 2015 Page 7...
- Page 8 The light conduit assemblies are made up of following components: • Conduit that contains the wiring • Unilet and bracket To mount and connect light conduit assemblies, proceed as follows: Attach the bracket to the channel using the Encore canopy light bracket and PEM stud as ® shown in...
- Page 9 Conduit Bracket (M14407A001) Note: The view is rotated by 180 degrees. Note: All conduit assemblies are placed in the same place in the unit regardless of lower frame type. MDE-4327B Encore® Canopy Light Kit (M03225K001) Installation Instructions · October 2015 Page 9...
- Page 10 Figure 4: Assembled Kit with M12630B001 Bracket Encore Canopy Light Conduit Bracket (M1263B001) Figure 5: Assembled Kit with M03205B003 Bracket Encore Canopy Light Bracket (M03205B003) Page 10 MDE-4327B Encore® Canopy Light Kit (M03225K001) Installation Instructions · October 2015...
- Page 11 Unilet and outside of the Unilet (cover removed), pulling the wires out until all the slack is taken up. After the slack wire has been removed between the Encore canopy light conduit and the Unilet, attach the conduit to the Unilet using the expansion union. Tighten the expansion union.
- Page 12 Appleton GRP LLC. ® © 2015 Gilbarco Inc. 7300 West Friendly Avenue · Post Office Box 22087 Greensboro, North Carolina 27420 Phone (336) 547-5000 · http://www.gilbarco.com · Printed in the U.S.A. MDE-4327B Encore® Canopy Light Kit (M03225K001) Installation Instructions · October 2015...
Need help?
Do you have a question about the Encore and is the answer not in the manual?
Questions and answers