Subscribe to Our Youtube Channel
Summary of Contents for Forest-Master ZERO BARROW
- Page 1 ZERO BARROW Patented No Strain, Self Levelling Barrow IMPORTANT: Read this manual fully before assembly and use and observe all safety rules and operating instructions...
- Page 2 Length 1400 mm 55 ins Width 710 mm 28 ins Height (excluding tub) 650 mm 26 ins Weight (excluding tub) 14 kg 31 lbs Wheel Size 4.80 / 4.00 x 8 Max Tyre Presure 2.0 bar 30 p.s.i. Zero Barrow...
- Page 3 Zero Barrow...
- Page 4 Hand grip Brace Sleeve M6 flange nut M6 x 40 cap head bolt Fork M12 axle bolt Wheel M12 plain washer Axle M6 x 5 grub screw Lifting ring front part Lifting ring rear part Self tapping screw Zero Barrow...
- Page 5 IMPORTANT: The barrow is supplied with 6 plain washers as depending on the fit of the wheel, it may be necessary to fit 2 washers on one side to space the wheel correctly. Zero Barrow...
- Page 6 Secure with an M6 flange nut (8). Note that the head of the cap head bolt should sit inside the large LARGER HOLE hole in the locating tube. See note on Page 7. Zero Barrow...
- Page 7 In Steps 4 & 5 you must insert the end with two equal di- ameter holes into the mount on the fork. In addition, the larger of the two holes at the other end should be orient- ed to the outside of the handle. Zero Barrow...
- Page 8 25 mm handle tubes so that the brace rests against the ends of the 30 mm handle tubes. Insert an M8 handwheel (3) into the nut on top of each brace top tube and tighten to secure the brace. Zero Barrow...
- Page 9 (17) are pre-drilled for the screws. STEP 10: Insert one of the lifting ring pivot tubes into one of the fork top tubes then compress the ring and insert the opposite pivot tube into the opposite fork top tube. Zero Barrow...
- Page 10 (3) into the nuts on the top of the fork top tubes but do not tighten. STEP 12: Push a handgrip (5) over the end of each of the 25 mm handle tubes. Ensure they are fully located on the handles. Zero Barrow...
- Page 11 Drag or lift the tub over the front of the ring so it sits within the ring. NOTE: The M8 handwheels on top of the forks should be loose so that the lifting ring is free to pivot. Zero Barrow...
- Page 12 It is important to place a foot on the axle to avoid the barrow moving backwards into the user. To remove the tub simply lift or drag it clear of the ring. Zero Barrow...
- Page 13 It is also possible to tighten the hand wheels on top of the forks, to stop the tub pivoting. The tub can then be emptied by raising the handles as in a conventional barrow, this however is gener- ally the least convenient. Zero Barrow...
-
Page 14: Important Safety Information
Check that the tyres are evenly inflated to a suitable pressure for the load you are carrying. Do not exceed the maximum pressure of 2.0 bar / 30 p.s.i. Zero Barrow... - Page 15 Should this product become defective, contact the store where it was purchased and either replacement parts will be issued, it will be repaired or it will be replaced free of charge. IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THIS PRODUCT. Zero Barrow...
- Page 16 Manufactured under license for Forest Master Limited. Registered Office: Forest Master Ltd, Industry Road, Heaton, Newcastle Upon Tyne, NE6 5XB, United Kingdom. Tel: +44 191 2966939 email: info@forest-master.com - web: www.forest-master.com Zero Barrow...
Need help?
Do you have a question about the ZERO BARROW and is the answer not in the manual?
Questions and answers