Subscribe to Our Youtube Channel
Summary of Contents for V7 42U
- Page 1 42U ENCLOSURE USER MANUAL RMEC42U 42U ENCLOSURE USER MANUAL • 42U ENCLOSURE USER MANUAL • 42U ENCLOSURE USER MANUAL 42U ENCLOSURE USER MANUAL • 42U ENCLOSURE USER MANUAL • 42U ENCLOSURE USER MANUAL...
- Page 2 Enclosure Enclosure Enclosure Enclosure Enclosure Enclosure • • • • • Installation Installation Installation Installation Installation Installation Caution! Read All Instructions and Warnings Caution! Read All Instructions and Warnings Caution! Read All Instructions and Warnings Before Installation Before Installation Before Installation Warning: Rack enclosures can be extremely heavy.
- Page 3 Caution! Read All Instructions and Warnings Caution! Read All Instructions and Warnings Caution! Read All Instructions and Warnings Before Installation Before Installation Before Installation Warning: Rack enclosures can be extremely heavy. Warning: Rack enclosures can be extremely heavy. Warning: Rack enclosures can be extremely heavy. Do not attempt to unpack, move or install the Do not attempt to unpack, move or install the Do not attempt to unpack, move or install the...
- Page 4 Overview • Overview • Overview • Overview • Overview • Overview 1. Roof panel 1. Roof panel 1. Roof panel 2. Locking split rear doors 2. Locking split rear doors 2. Locking split rear doors 3. Locking side panels 3. Locking side panels 3.
- Page 6 Unpacking • Unpacking • Unpacking • Unpacking • Unpacking • Unpacking Once the enclosure is close to the installation space and upright and stable – use a utility knife to cut the shrink wrap and remove the outer packaging. Once the enclosure is close to the installation space and upright and stable – use a utility knife to cut the shrink wrap and remove the outer packaging.
- Page 7 Use wrench to raise leveling feet higher than the casters before moving enclosure off pallet Use wrench to raise leveling feet higher than the casters before moving enclosure off pallet Use wrench to raise leveling feet higher than the casters before moving enclosure off pallet Use wrench to raise leveling feet higher than the casters before moving enclosure off pallet Use wrench to raise leveling feet higher than the casters before moving enclosure off pallet Use wrench to raise leveling feet higher than the casters before moving enclosure off pallet...
- Page 8 Placement • Placement • Placement • Placement • Placement • Placement Move the enclosure with the casters for short distance on level smooth ground by pushing from front or rear. WARNING: Do not push or pull the enclosure at the side panels Move the enclosure with the casters for short distance on level smooth ground by pushing from front or rear.
- Page 9 WARNING: Enclosure must be level before installing equipment. Use the levelers to provide long-term support, casters are not designed for this. Install the enclosure in an area with a level floor that is structurally able to handle the weight. WARNING: Enclosure must be level before installing equipment. Use the levelers to provide long-term support, casters are not designed for this. Install the enclosure in an area with a level floor that is structurally able to handle the weight.
- Page 10 Optional • Optional • Optional • Optional • Optional • Optional Optional: Reversing Front Door Warning – Do not attempt without assistance Warning – Do not attempt without assistance Warning – Do not attempt without assistance Warning – Do not attempt without assistance Warning –...
- Page 11 ex: 1 ex: 2 ex: 3 ex: 4 ex: 5...
- Page 12 Optional • Optional • Optional • Optional • Optional • Optional Remove Roof Panel 1. Pull the 2 pins near the back of roof panel, and while holding push the roof panel upwards. 2. Remove the roof panel from slots in the enclosures frame and lift to remove Remove Roof Panel 1.
- Page 13 Remove Side Panels 1. Remove ground wire. 2. Slide side latches inwards 3. Swing out and pull up Remove Side Panels 1. Remove ground wire. 2. Slide side latches inwards 3. Swing out and pull up Remove Side Panels 1. Remove ground wire. 2. Slide side latches inwards 3. Swing out and pull up Remove Side Panels 1.
- Page 14 Enclosure Enclosure Enclosure Enclosure Enclosure Enclosure • • • • • Configuration Configuration Configuration Configuration Configuration Configuration Adjust Mounting and Cable Management Rails. Warning: Do not attempt without assistance. Do not adjust rails while equipment is installed. The 4 mounting rails are preinstalled and can be adjusted independently. 1.
- Page 15 Adjust Mounting and Cable Management Rails. Warning: Do not attempt without assistance. Do not adjust rails while equipment is installed. The 4 mounting rails are preinstalled and can be adjusted independently. 1. Each rail is connected to the enclosure with 6 screws –1 pair at the upper beam, at the middle and at the bottom 2.
- Page 16 Equipment Equipment Equipment Equipment Equipment Equipment • • • • • Installation Installation Installation Installation Installation Installation Warning: Do not install equipment until you have stabilized the enclosure. Install heavier equipment first towards the bottom of the enclosure. Install equipment starting from the bottom of the enclosure and proceed toward the top of the enclosure - never the reverse. If using sliding equipment rails, be careful when extending the rails.
- Page 17 Note: The square holes in the middle of each rack unit are numbered and also include a small notch to aid identification. A single rack unit includes the space occupied by the numbered hole and the holes directly above and below. Note: The square holes in the middle of each rack unit are numbered and also include a small notch to aid identification.
- Page 18 The enclosure comes with mounting rails that have square holes for mounting rack equipment. To install equipment, use the included cage nuts and other hardware. The enclosure comes with mounting rails that have square holes for mounting rack equipment. To install equipment, use the included cage nuts and other hardware. The enclosure comes with mounting rails that have square holes for mounting rack equipment.
- Page 19 Locate the numbered square openings in the mounting rails where you plan to install your equipment. Install cage nuts (included) into the square openings by pressing it in. This provides an attachment point for the cage bolts (included) Locate the numbered square openings in the mounting rails where you plan to install your equipment. Install cage nuts (included) into the square openings by pressing it in. This provides an attachment point for the cage bolts (included) Locate the numbered square openings in the mounting rails where you plan to install your equipment.
- Page 20 Equipment Equipment Equipment Equipment Equipment Equipment • • • • • Installation Installation Installation Installation Installation Installation When the cage nut is properly installed, both flanges will protrude through the square opening and will be visible on the outer surface of the mounting rail. Repeat until all required cage nuts are installed.
- Page 22 Safety Safety Safety Safety Safety Safety • • • • • Instructions Instructions Instructions Instructions Instructions Instructions • Keep the enclosure in an indoor environment, free from dust, moisture, direct sunlight and extreme temperature. • Leave adequate space at the front and rear of the enclosure for proper ventilation. Do not block, cover or insert objects into the external ventilation openings of the enclosure. •...
- Page 23 • Keep the enclosure in an indoor environment, free from dust, moisture, direct sunlight and extreme temperature. • Leave adequate space at the front and rear of the enclosure for proper ventilation. Do not block, cover or insert objects into the external ventilation openings of the enclosure. •...
- Page 24 7/19/2016...
Need help?
Do you have a question about the 42U and is the answer not in the manual?
Questions and answers