Summary of Contents for Navilock NL-82052RS
- Page 1 Engine module u-blox NEO-M8U UDR GNSS receiver NL-82052RS, NL-82052USB und NL-82052TLL manual (62764, 62763, 62745)
- Page 2 At the next trip meeting the above criteria it will be automatically recalibrated. 1.1. Contents* 1 x Navilock engine module 1 x 8 cm CD ROM including operation manual * Before using the device, please make sure that all the parts are included in the package. If any parts are...
- Page 3 Important health and safety information • When using this product, take the following precautions in order to avoid possible damages and legal consequences. Always follow all safety and operation manuals exactly and keep them for future reference. Observe all warnings in the operation manual and on the product. In order to avoid injuries, electrocution, fire and damages to the product, observe the following precautions: •...
-
Page 4: General Information
2. General information 2.1 NL-82052RS = Item 62764 On the serial engine module, a USB to serial bridge is built. The u-blox chipset incorporates a USB standard output. It must be converted from USB to serial. PIN1 is at the level of the shield plate and PIN6 at the cut edge of the module. - Page 5 4.1 NL-82052RS serial Serial signal level which is necessary for the operation of the NL-83052RS. 4.2 NL-82052USB USB 1.1 A standard USB 1.1 port is required to operate the NL-82052USB necessary. 4.3 NL-82052TTL TTL TTL signal levels to operate the NL-82052TTL needed.
- Page 6 The u-center can set the output mode of action, such as 1Hz to 10Hz and other. As below Please noted the TIMEPULS settings have two item 0-TIMEPULS is for PPS_OUT 1-TIMEPULS2 is for LED...
-
Page 7: Application Environment
5. Application environment The USB Engine module can be installed on Windows 7/8.1/10, CE and Linux operating a GNSS receiver. But it is not suitable for WINDOWS 98/98SE/Me or MAC OS. No drivers are available for this purpose. The serial and TTL version can be used without dependencies to the OS. There's only concerning the restriction of u-center testing tools, it is available only for Windows 7/8.1/10 and CE. - Page 8 The choice of which GNSS want to use, take as follows: View\Configuration View You can select your GNSS system and the combination of several systems on the right side. The following combinations are available: RTCM GNSS SBAS Galileo GLONASS BeiDou QZSS EGNOS WAAS...
- Page 9 7. EGNOS configuration with u-center 8.24 View\Configuration View The engine module use EGNOS as default. In the configuration menu you can check these options. For detailed information please use the documentation from u-blox http://www.u- blox.com/images/downloads/Product_Docs/u-Center_User_Guide_(UBX-13005250).pdf. Further information to the u-center can be found in the u-blox documentation under http://www.u- blox.com/products/u_center.html.
- Page 10 8. AssistNow configuration with u-center 8.xx The engine module supports AssistNow! AssistNow is a standard A-GNSS service, which increases the performance of the GNSS receiver, by calculating a position almost immediately, even under difficult reception conditions. A-GNSS improves all GNSS capable applications, especially those that require a continuous state of readiness, for example applications for fleet management or GNSS capable hand-held devices, whose users would like to access local services immediately, independently of the reception conditions.
- Page 11 The Navilock repair centre tries to be as obliging as possible, so please tell us the real reason for the defect. During the error analysis, we can generally detect if the cause for the defect was an external cause, water damage, fall, over-voltage or the wrong handling of the unit.
- Page 12 10. Technical specifications Chip set manufacturer/type: ublox-8 NEO-M8U Channels: Sensitivity: -160 dBm Frequency: GPS: L1, 1575.4200 MHz BEIDOU COMPASS: B1, 1561.0980 MHz GALILEO: E1, 1575.4200 MHz GLONASS: G1, 1602.5625 - 1615.5000 MHz Target precisions: Position horizontal: GPS/SBAS/QZSS+GLONASS: 2.0 m CEP Time: 1 microsecond synchronized with GPS time Speed:...
- Page 13 Navilock. The brand Navilock is a registered trademark and may not be used without the written authorization of the trademark owner. In no case may it be altered or completed by additions.
- Page 14 WEEE note The WEEE (Waste Electrical and Electronic Equipment) directive, which came into force on 13 February 2003, lead to a comprehensive change in the disposal of used electric products. It is the main purpose of this directive to avoid electric waste products (WEEE), while simultaneously promoting the re-usage, recycling and other forms of reconditioning in order to reduce the amount of waste.