Related Manuals for Chapman PC120
Summary of Contents for Chapman PC120
- Page 1 PC120 Paddock Cleaner Original Instructions Chapman Machinery Ltd, Hele Barton, Week St. Mary, Holsworthy, Devon EX22 6XR Tel: 01288 308149 Email: sales@chapman.co.uk...
-
Page 2: Table Of Contents
The information contained in this manual is correct at the time of going to press. However, in the course of development, changes in specification are inevitable. Should you find the information given differs from your machine, please contact Chapman Machinery Ltd direct for advice. Use only Chapman Genuine Service Parts on Chapman Machinery and Machines. -
Page 3: Hse Information
HSE Information Safe use of all-terrain vehicles (ATVs) in agriculture and forestry – AIS Sheet 33 Remember that your ability to control the ATV by your body Introduction movements will be considerably reduced when carrying a load or towing a trailer. This information sheet gives advice on the safe use of ATVs. -
Page 4: Important Safety Information
Important Safety Information Always read this manual before fitting or operating the machine – whenever any doubt exists contact your dealer or the Chapman Machinery Service Department for advice and assistance. DEFINITIONS The following definitions apply throughout this manual: WARNING - An operating procedure, technique etc., which can result in personal injury or loss of life if not observed carefully. -
Page 5: Description
Description The PC120 Paddock Cleaner is designed to pick up horse dung and other debris with ease to make paddock maintenance quick and easy. The PC120 Paddock Cleaner is a trailed attachment, with 4 Polyethylene brushes powered by a Honda GX200 6.5hp Engine collecting dung into a 550 (approx.) litre hopper. - Page 6 Assembly of Machine The PC120 Paddock Cleaner is delivered vertical on a pallet for ease of transport. The PC120 needs some minor assembly prior to use. Please see instructions below on assembling the PC120 from dispatch: Tools needed: 17, 19 & 24mm Spanners Lower the PC120 gently down with supports beneath the black skid plates.
- Page 7 Firstly, install the 19mm bolt to the bottom rear of the mount, offer the drawbar up and fit the bolt, washers and nut loosely. Next, install the other 19mm bolt & nut in through the most forward hole and again, loosely. Supporting the weight of the drawbar, lift up until the drawbar adjuster is inline with the last 24mm bolt fitment at the back of the drawbar mount &...
- Page 8 Do not overtighten the bolts, they only need to be just ‘nipped’ up to allow the drawbar to move up and down when the adjuster is used. Next, install the Jockey wheelby unwinding the jockey clamp, install the jockey wheel assembly into the clamp and tightening securely.
-
Page 9: Component Identification
Component Identification Page 9... -
Page 10: Identification
Identification Each machine is fitted with a serial plate (shown below) which details the following: Model 2. Date of Manufacture (DOM) 3. Serial Number 4. Mass When enquiring regarding spares or additional equipment, ensure you have this information to hand. Implement Decals If your implement does not contain all of the decals shown below, please contact your equipment supplier for replacement decals before use. -
Page 11: Attachment
3. Attach the control cable to the control socket fitted on the towing machine, ensuring a secure connection. NOTE: PC120 Models are fitted with a combined throttle / choke / stop cable. This provides the emergency stop function should it be required. (Remote throttle for quad use) -
Page 12: Initial Set-Up
Initial Set-up Fuel Tank & Gearbox The PC120 comes with engine & gearbox oil topped up. Prior to use, make sure you remove the protective tape on top of the fuel tank, and breather pipe. (see below) Height Hitch the PC120 up to the towing vehicle, adjust the height of the roller to the desired level by actuating the height adjustment jack. -
Page 13: Operation
Tipping Mechanism The PC120 comes with electric tipping. To operate the electric tip, this is done via a simple two button control for open & close (see below). The tipping will stop when it’s reached full travel in either direction. Click switch back to the ‘neutral’... -
Page 14: Maintenance
Maintenance All maintenance, cleaning and repair operations must be performed with the machine suitably supported, the engine switched off (and cool), and the ignition keys removed. NOTE: For commercial use, log hours of operation in a maintenance booklet to ensure proper maintenance intervals and continued service. -
Page 15: Warranty
Transfer of Warranty The Chapman warranty be transferred to a subsequent owner of the machinery (for use within the UK only) for the balance of the warranty period subject to all of the stated warranty conditions and provided that the Change of Owner form is completed and sent to Chapman Machinery within 14 days of change of owner- ship. -
Page 16: Ec Declaration Of Conformity
Chapman Machinery Ltd Hele Barton Week St. Mary Holsworthy Devon EX22 6XR The Products Covered by this Declaration Product: PC120 Paddock Cleaner Standards and Regulations used: Machinery Directive 2006/42/EC Place of Issue: United Kingdom Name of Representative: James Chapman Position of representative:...