Glamox Production GmbH & Co. KG Glasower Weg 5, 17166 Teterow, Germany www.glamox.com/gmo We would also like to use this opportunity to thank you for choosing Norselight as your supplier of marine searchlights. Guarantee The guarantee is only valid against production faults. It do not cover damage caused by transportation, damage due to disregard of this technical Manual or adverse external effects.
Table of contents Introduction ............................3 Guaranty ............................... 3 General description ........................5 Searchlight ..........................5 The motor housing ........................5 Control panel ........................... 5 The Ethernet Switch: ......................8 High Sensitive Receiver: ......................8 Main Control Panel position indicator versus searchlight position: ........10 Power Supply (Rectifiers): ....................
1 General description 1.1 Searchlight The searchlights XS 500-1000-1600-2000 and XS 3000 are made from seawater resistant aluminium, welded and finished with white powder coat. The lamp housing basically contains one a lamp, a glass-reflector covered with silver, noise filters and a focus-motor for adjustment of the light beam. 1.2 The motor housing The R50 motor housing is made from seawater resistant aluminium and finished with white powder coat.
1.4 The Ethernet Switch: It contains: • 5 port x RJ45 • DIN rail mounting • Power 24V DC + ground 1.5 High Sensitive Receiver: The Access Point is a high sensitive receiver for the wireless panel build for maximum range and durability. The Access Point communicate with the wireless bus, witch remotely controls the searchlights with R50 motor unit.
Page 9
Features and Benefits: • Wireless receiver for SCS wireless Bus • Bolt-on to Norselight`s network of searchlights • Weatherproof Aluminium Casing, Compact and new design • Based on TCP/IP technology • Waterproof, quick disconnect RJ-45 connector • Custom made for Offshore •...
1.6 Main Control Panel position indicator versus searchlight position: In accordance to MSC/Circ. 982 Pos 5.5.1 “Movement of Controllers” and 5.5.2 “Corresponding Movements “ The position indicator on the Main Control Panel indicates the position of the searchlight. 0 position on the panel indicates that the searchlight is positioned straight forward compared to the searchlight 0 position.
Page 12
EX-30 G/1 EX30-G/1, single phase 90-265V 50/60Hz electronic power supply is specifically suitable for feeding 250 to 500W short arc Xenon lamps. Weight 8kg. Further instructions in Installation guide for Rectifier. 1. Lamp ON/OFF switch IMPORTANT NOTE: DO NOT USE THIS SWITCH FOR THE REMOTE CONNECTION ! 2.
Page 13
PX-50 N These extremely compact rectifiers for single-phase inputs have been designed to feed 1000W Xenon lamps, meeting the requirements of lamps manufacturers to ensure correct operation and long life of the lamp. The units are fitted with a transformer with taps for output lamp power regulation and a special circuit to avoid the lamp turn off during the tap switching.
Page 14
EX-100 D/1 This electronic power supply for single phase or double phase 230Vac 50/60Hz input, has been designed to feed from 1000W to 3000W short arc Xenon lamps, meeting all the requirements of lamp manufacturers to ensure correct operation, long life to the lamp, and high reliability. Weight 18 kg. Further instructions in Installation guide for Rectifier.
Page 15
N3-80 / N3-150 These high quality rectifier power supplies have been expressly designed to ensure the correct operation and long life of short arc Xenon lamps. These units, developed to meet the recommendations of Xenon lamp manufacturers, are fitted with special IREM transformers with adjustable magnetic shunt for continuous output regulation over the entire operating range.
2 Technical data 2.1 Xenon Searchlight Properties Value Searchlight XS 500 XS 1000 XS 1600 XS 2000 XS 3000 890 mm 930 mm 930 mm 1020 mm Dimension Height: Width: 470 mm 515 mm 515 mm 615 mm Weight of searchlight: 46,5 kg 49,5 51,5 kg...
2.2 Main Operation Panel Standard IEC 60945 Ed4 (2002-08) Number of panels Standard max 9 pcs in one system Network Star and Tree network topology. Interface RJ45 port 10/100 LAN cable CAT5e - CAT7 twisted (568b) Power Requirements Power input: 24VDC (18-30VDC) Power consumption: <3.5W Physical Characteristics Casing: IP22 protection Dimensions(WxHxD): 147x160x43,4 mm (5.8x6.3x1.7 in)
2.5 Switch KIEN1005 Standard IEEE802.3 IEEE802.3u IEEE802.3x IEEE802.1p Store and forward switching mode MAC Address Table Size Chain and star network topology. Network Service Diagnostics: LEDs(power, link status, port rate,) Port priority: QoS for 5th port (default high priority) Current over-load protection: Yes(AC220V) Reverse polarity power connection protection: Yes Broadcast storm protection: Yes Interface...
2.6 Access Point High Sensitive Receiver for Wireless Operation Panel REGULATORY/ COMPLIANCE INFORMATION Wireless Approvals FCC, IC, CE RoHs Compliance IP/NEMA Compliance IP67/ NEMA 6 DIAMETER RANGE PERFORMANCE 11Mbps 200m 5.5Mbps 400m 2Mbps 800m 1Mbps 1600m RADIO OPERATING Frequency 2412-2464 MHz TX Power 15dBm (20dBm EIRP including Antenna) RX Sensitivity...
3 Installation 3.1 Mechanical installation • The searchlight must be mounted on a horizontal surface using 4 stainless screws. • The Main/Slave Operation Panel and the Switch is designed for installation in indoor applications. • The Access Point is designed for out side installation. •...
3.3 BUS installation • The BUS communication system requires minimum LAN CAT5e, 4 pair shielded twisted pair cable. • All connection entries need RJ45 connector using T-568B cable standard. • Make sure that all cable entries maintain their shield protection. Note: Follow the installation requirements from your cable supplier! Avoid brakeage on the Ethernet connectors (panel, switch and searchlight COM...
Operation 4.1 Operation Panels function LED-indication display: • Searchlight number in use • Indication level of Dim-light intensity. • Indication level on vertical and horizontal speed. • End stop indication T +/-180 • Alarm indication A, when stop occurs before end stop. Searchlight selection: •...
4.2 Change of the lamp Warning! When changing the bulb, use facial protection and leather gloves as accidental breakage of the glass bulb can critically harm anyone within a radius of 8m. Note: Do not touch the bulb with bare hands or with anything greasy. The bulb must be clean.
Page 29
Operation Panel (Main and Slave) w/cut dimensions...
Page 30
The Switch BUS dimensions. Fits for 5 LAN cable entry for RJ45 plug (KEIN1005S-5T) or 1 one full-duplex fiber port of 100Base-FX, single mode or multimode and 4 LAN cable entries (KEIN1005-1S (M)-4T). Look in the manual for KEIN1005 for more details.
Page 44
Cable 1 TB1 1 & 2 Cable 3 TB1 L1 & L2 Ground connection Cable 2 Cabel 4 TB2 +/- Junction Box connections All installation cables enters from the right side looking directly into the Junction Box through 2x M20, M25 and M32 as explained in earlier dimension drawing.
Page 45
Connecting diagram Main and Slave Operation Panel...