Advertisement
Quick Links
6/1/15
sales@glasscraftersinc.com
Installation Instructions
Model By-Pass Sliding Doors
Tub or Shower By-Pass Sliding Doors
with Inline Panel ETI - ESI or with Inline Buttress Panel ETBI-ESBI
By Pass Sliding Doors
Shower Enclosure
Tub Enclosure
IF YOU NEED REPLACEMENT PARTS OR HAVE INSTALLATION QUESTIONS,
PLEASE CALL OUR CUSTOMER SERVICE REPRESENTATIVES.
INSTALLATIONS SHALL BE MADE ACCORDING TO MANUFACTURER'S INSTRUCTIONS AND DRAWINGS.
GLASSCRAFTERS RECOMMENDS THE INSTALLATION TO BE PERFORMED BY A TRAINED INSTALLER.
888-683-1362
Advertisement
Related Manuals for GlassCrafters EPIC Series
Summary of Contents for GlassCrafters EPIC Series
- Page 1 Shower Enclosure Tub Enclosure IF YOU NEED REPLACEMENT PARTS OR HAVE INSTALLATION QUESTIONS, PLEASE CALL OUR CUSTOMER SERVICE REPRESENTATIVES. INSTALLATIONS SHALL BE MADE ACCORDING TO MANUFACTURER’S INSTRUCTIONS AND DRAWINGS. GLASSCRAFTERS RECOMMENDS THE INSTALLATION TO BE PERFORMED BY A TRAINED INSTALLER. 888-683-1362...
- Page 2 For 1/4” GLASS FOR 3/8” GLASS Item No. Description Qty. Item No. Description Qty. Header Header Base Base Wall Jamb Wall Jamb Glass Door Glass Door Glass Door Glass Door Base Vinyl Base Vinyl Jamb Bumper Jamb Bumper #6 x 1/2” Screw #6 x 1/2”...
- Page 3 Installation shows 3/8” glass by-pass shower enclosure with two standard towel bars. Other units may vary. Installation shows Round Header. Flat header is Optional. ROUND HEADES SECTION FLAT HEADES SECTION View form Inside of Tub/Shower...
- Page 4 Installation Instructions for GlassCrafters Epic By-Pass Shower Enclosure IMPORTANT: Read all instructions carefully and become familiar with all parts before installation. Unpacking: Care should be taken unpacking your Shower Enclosure. Place the Glass Panels in an upright, Safe location to avoid damage. Never place glass directly on hard surface.
- Page 5 Channel #22 is cut to size on factory. Set the Base Channel #22 on the base and mark holes for screw anchors (Sketch 3A). Remove the channel. Drill all marked holes and, clean the Tub/Shower Enclosure ledge and the Base Jamb areas thoroughly. Insert Wall Anchors #11 into the drilled holes and install Base Channel using Screws #12 as shown in Sketch 3B.
- Page 6 Base #2 is left oversized on factory and must be cut on job site. Measure dimension “D” from end of base channel #19 to opposite wall (Scetch 5A). Subtract 1 ¼ from dimension “D” . The result is the exact size for Base #2. Cut Base# 2 to size. Please Note: to obtain the best results, use a carbide tooth metal cutting chop saw or metal hack saw.
- Page 7 Carefully slide into tempoary position 180 deg inline post # 20 and wall jamb # 3 as shown in Sketch # 7A Use level and tape-measure to make sure that 180 degree post is plumb. Use few strips of masking tape to secure the extrusions and the glass. Inside of Shower Wall Channel Wall Jamb...
- Page 8 Set Header #1 on wall Jams#3 (Sketch 9A). Use a level to make sure header is level. Mark hole location for Header Bracket#28. Remove Header#1, Drill the hole and insert Anchor#11. Working from inside of the hower will make the access to bracket easier. Mark Header Bracket hole locations here.
- Page 9 Insert Header Filler # 15 as shown in Sketch 11 A away for panel location. Slide the Header down on top of the Round Header shown. Yours may Differ. Wall Jamb #3 and Wall Channel #19 as shown Using an long screwdriver insert and fasten Screw# 12 into the Header Bracket #28 Inside of Outside of...
- Page 10 Glass hangers are installed on to glass panels at factory. Warning: The Glass Panels are heavy and awkward. It is recommended that two people lift and hang the glass panels. DO NOT LIFT GLASS PANELS BY THE TOWEL BARS/PANEL PULLS. Step 1 Step 2 Step 3...
- Page 11 Glass hangers are installed on to glass panels at factory. Warning: The Glass Panels are heavy and awkward. It is recommended that two people lift and hang the glass panels. DO NOT LIFT GLASS PANELS BY THE TOWEL BARS/PANEL PULLS. Step 2 Step 2 Step 1...
- Page 12 There should be 1/4-5/8 space between bottom edge of the glass and Base (Sketch 10A). That space is necessary for Center Guide. If it is less or more than mentioned limits the rollers must be moved up/down. Readjusting Rollers on the Glass Hanger. NOTE: this step is only performed if necessary.
- Page 13 Clean the metal perimeter free from dust and construction debree. Apply Silicone Sealant as shown Be sure to add Silicone to both ends of the Base Apply Silicone Sealant both ends where it meets the Wall , as shown in SKETCH 13 A.
Need help?
Do you have a question about the EPIC Series and is the answer not in the manual?
Questions and answers