Advertisement
3.1.2. Locate the pressure gauge inlet hole in the head of the press hydraulic system and remove the dust plug with a hex key, (this may
be very tightly secured). Note: There is no pressure gauge on the YK15BLG.3.1.3. Fitting pressure gauge.
a) For models with integral hydraulic system screw gauge angle arm (retain white tape around thread) into inlet hole, Find the outlet
hole by feeling through the tape and ensure the final tightening of the arm leaves the outlet facing upward. DO NOT over tighten.
Remove the masking tape carefully exposing the rubber seal which must lay flat in the bottom of the outlet hole.
b) Remove the pressure gauge from carton and screw into the angle arm securing with a spanner.
c) For models with a standard hydraulic system (YK15, YK30,) screw the pressure gauge directly into the system inlet hole
by holding the gauge to the front and turning the nut at the head of the connector.
3.1.3. For installation see chapter 4.
3.1.4. Once installed, screw the pump handle into the pump arm.
3.1.5. Insert the work table pins through holes in the main frame and carefully place the work table between the frame upright
lowering it onto the pins accordingly. F WARNING! Take care not to allow the working table to drop onto the pins and ensure your
hands and fingers are clear of the working table when lowered.
3.1.6. Place v-blocks on work table ready for use. Take care to ensure the v-blocks do not fall from the work table.
4. INSTALLATION & OPERATING
4.1.
INSTALLATION.
4.1.1. Securely attach the press to a flat, firm, level surface taking into account clearance for working pieces. Should you wish to mount
a bench press on a workbench or surface, ensure the bench is flat and level and is strong enough to support the press
and any workpiece during operation.
4.1.2. Purge hydraulic system.
Before operating the press, purge the hydraulic system in order to eliminate any air that may have built up during transit. Open the release
valve and pump the handle several times. Should the system malfunction at any time, repeating this process may resolve the problem.
I
DANGER! Models are purpose designed to withstand greater loads than the hydraulic units can develop. For safety reasons, always ensure
I
the workpiece is secured on table and loads that flex will not suddenly “give” causing danger to operator or damage to component. Also ensure
s
s
you have read and understood chapter 1 safety instructions.
4.2.
OPERATING INSTRUCTIONS.
4.2.1. Using press adjustable table support pins place the press working table at the required operating height.
4.2.2. Check that the hydraulic unit is fully closed ready for operating.
4.2.3. Place workpiece onto the work table or the two arbors appropriately positioned. Position the head of the hydraulic unit on the centre
of the workpiece using appropriate extension. Note: care must be taken to ensure an arbor does not fall from the press worktable.
4.2.4. DO NOT exceed the stroke indicated on the label or the red mark on the piston.
4.2.5. DO NOT apply off centre loads.
4.2.6. When work is complete release the pressure and the piston and the ram head will retract automatically.
Note: Always keep the piston, extension screw and pump piston retracted after use.
5. MAINTENANCE
Note: Maintenance and repair must only be carried out by qualified person. Contact your Sealey dealer for details.
5.1.
Lubricate all moving parts at regular intervals.
5.2.
Always keep the press clean, dry, and protected from harsh conditions.
5.3.
Should you need to replace oil ensure piston is fully retracted. An excess of oil will render press inoperative. Use only appropriate
Sealey hydraulic oil. DO NOT use brake fluid. Contact your local Sealey dealer for details. Purge the system to remove any air.
5.4.
Check your model parts information for spares. Repair kits are also available.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE MACHINE.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN PRODUCT TO US. Please telephone us on 01284 757500 to obtain the address and phone number of your local agent.
If product is under guarantee please contact your dealer.
De-commissioning Product
Should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose
of the product and the oil according to local regulations.
Declaration of Conformity We, the sole importer into the UK, declare that the
EEC standards and directives.
Hydraulic Press Models
YK10BM, YK15, YK15BLG, YK15BM,
YK15FM, YK30, YK30FM, YK50FM.
Machine Directive (S.L. 1992/3073)
93/68/EEC CE Marking Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No responsibility is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date. Proof of purchase
will be required for any claim. INFORMATION: Please call us for a copy of our latest catalogue
s
Sealey Group,
Bury St. Edmunds, Suffolk.
products
listed below
The construction files for
these products
and may be inspected on request by contacting Jack Sealey Ltd
Signed by John Sealey
For Jack Sealey Ltd. Sole importer into the UK of Sealey
01284 703534
01284 757500
YK10BM, YK15, YK15BLG, YK15BM, YK15FM, YK30, YK30FM, YK50FM. - 0025 -050897
are
in conformity with the following
are held by the Manufacturer
Date
1st September
1998
Quality Machinery
E-mail: sales@sealey.co.uk
Advertisement
