Advertisement
Quick Links
FAST Installation (PMRS 104)
Release date: April, 2017
Preface: This manual Consists of 3 main parts:
Chapter one:
Introduction
Chapter two:
Hardware interfaces
Chapter three:
Installation
SIM Data Card
Camera(s)
Micro SD Card
Required Items
A Micro SD Card is required for
recording in the MRS device. The
speed of the SD Card will vary
depending on the make.
SDs with storage above 32GB have to
be formatted to a FAT32 format
(through third party apps).
4G/3G/HSPA/EDGE
SIM Data Card from a cellular
provider is required for the unit.
Any HD camera with HDMI
connection can be connected to
the PMRS unit.
Advertisement
Related Manuals for INFODRAW PMRS-104
Summary of Contents for INFODRAW PMRS-104
- Page 1 FAST Installation (PMRS 104) Release date: April, 2017 Preface: This manual Consists of 3 main parts: Chapter one: Introduction Chapter two: Hardware interfaces Chapter three: Installation Required Items SIM Data Card 4G/3G/HSPA/EDGE SIM Data Card from a cellular provider is required for the unit. Any HD camera with HDMI Camera(s) connection can be connected to...
-
Page 2: Chapter 1 - Introduction
Chapter 1 - Introduction 1-1 Introduction: Infodraw PMRS is a portable handheld multimedia streaming and monitoring system from the field. It allows users to stream live video/audio/location from anywhere over the cellular 4G/ 3G/ HSPA/ EDGE networks and can be monitored from any location upon alarm/ request. The media streaming is done using PMRS units which can be carried handheld or located either on mobile vehicles or fixed locations. - Page 3 1-3 System Architecture: Server-Based – M2M (recommended). This architecture is based on a server with a fixed IP address. Multiple units can communicate with the server as well as multiple clients. All clients are connected to the server and have viewing and control capabilities.
-
Page 4: Chapter 2 - Unit Hardware Interfaces
Chapter 2 - Unit Hardware Interfaces 2-1 Video Input/ Audio Input/ 5V Power Output: The unit has a standard HDMI which supports the video input and audio. 2-2 GPS Antenna Connector: The GPS antenna has a SMA interface located on the top of the PMRS unit. Connect the GPS antenna to the SMA connector 2-3 GSM Antenna Connector:... - Page 5 The USB client is used for configuring the 2-6 USB Client: device’s parameters using the Device Config application. Connect the USB cable between here and a PC when configuring the unit. Dip switch must be set correct in order to communicate through usb 2-7 Micro SD Slot: Insert a Micro SD card into the Micro SD slot for...
- Page 6 2-12 LEDs: The PMRS has 3 LEDs located on the top side of the unit. The 3 LEDs indicate the following: 1) Green LED – External power is connected. 2) Red LED – Software status, blinks when software is running. 3) Blue LED (on) –...
- Page 7 2-13 I/O Cable: The i/o Cable has several different coloured wires for specific purposes such as PTZ and GPIO. The definitions of the wires are listed below. HDMI COLOR FUNCTION BLUE GPIO IN 1 WHITE-BLACK GPIO IN 2 ORANGE 12V ON RED-BLACK EXTERNAL ON GREEN...
-
Page 8: Chapter 3 - Installation
Chapter 3 - Installation PMRS software can be downloaded from http://www.infodraw.com/dlds The Installation section is divided to 3 parts: Installation of servers 2. Change setting MRS configurator (WIN 8,10 Android app) 3. Installation of MRS monitor (watch video) 3-1 Installation on Server Computers 1. - Page 9 3-2-1 Set parameters via PC (Device Configurator – 7 and below) 1. Browse to the website: www.infodraw.com/dlds 2. Open the folder of the latest version of the PMRS ("6.1.0.2" for example). 3. Enter the “MRS device config” folder and activate the Setup_MRS_DeviceConfig.msi file.
- Page 10 3-2-3 Set Parameters on the Device (on PC computer) 1. Once the unit is connected to the PC, parameters are loaded. 2. Go to connection screen. 3. Change the IP (of the server IP). 4. Save parameters (write to device- in the "File" menu) or click on the candle icon that is placed on the top-left side of your screen.
- Page 11 3-2-4 Set Parameters via Android (MRSconfig) Attention! This feature is only available in PMRS 201/104/410 devices MRSConfig Activation: Look for the MRSConfig app in your "google play" store, download it - the application is free. Step 1: Prepare the DIP switches, the left DIP switch needs to be in a "down" position and the right DIP switch needs to be elevated Step 2: Activate the PMRS Device Step 3: Activate the Bluetooth feature on your Android phone and Click on the...
-
Page 12: Watch Video
3-3 Watch video 1. Open your browser to www.infodraw.com/dlds 2. Open the folder of the latest MRS version and in it, open the folder of the Monitor-Client. 3. Run the Setup_MRS_Client.msi file and install the program. 4. After installation is complete, open the MRS Monitor program.