Download Print this page
Bayco UVR-9014 Quick Start Manual

Bayco UVR-9014 Quick Start Manual

Cordless fluorescent lamp and platform

Advertisement

Quick Links

BAYCO MODEL UVR-9014 CORDLESS FLUORESCENT LAMP AND PLATFORM
Direct eye Exposure to Ultra Violet Light can Damaged the eyes.
Never expose the handle unit or charger to water, rain, snow or mist.
Do not charge the batteries in the presence of flammable gases or liquids.
Do not allow the two positive (
top of the charger platform to touch each other, bend in to each other, or short together.
Charge the lamp handle or charging platform with room or car temperature between 50ºF and 105ºF (10ºC ―
42ºC).
Only use a 120V outlet for the AC power cord, and a 12V DC car outlet for the DC cord. Do not try to use an
engine generator, a step-up transformer or any other external power supply.
Never try to charge non-rechargeable batteries with this charger.
Do not try to repair or disassemble this charger or the handle battery packs. If you experience problems, call us
during normal business hours at the number listed elsewhere in this booklet.
Do not dispose of dead battery packs in a fire or by burning.
Do not recharge in direct sunlight.
Young children should be supervised to assure that they do not play with the handle unit or charger platform.
1.
Only use the Bayco battery pack bases and charging platforms.
2.
Plug the charger platform into the power source using the proper cord: 120V AC wall plug or the 12V DC auto
adapter plug. Only charge the pack between 50ºF and 105ºF.
3.
Simply plug the lamp or the platform into the proper power source.
4.
Do not allow anything to cover the lamp or platform during recharging.
5.
To use the recharging platform, turn the handle battery pack upside down and away from you, and press
the tabs into the locking cradles. You cannot make contact unless the pack is upside down and facing away
from you. Insert the handle pack down until it won't go any further. Do not try to twist or force the battery pack onto
the charging platform.
6.
The
red
indicator light will come on either the lamp or the platform when the pack is properly inserted on
the platform, and it will stay on until the pack is fully charged. The total time needed to recharge the pack will vary,
depending upon how charged the batteries are when you start. Even totally charged packs will charge for about 8
minutes before the red light goes off and the green light comes on.
7.
The
green
light will come on when the battery pack is fully charged. The time required to recharge will be
between 20 and 140 minutes, but will average about 100 minutes. The
being charged.
8.
Don't try to recharge a lamp or a battery pack that is already hot. When recharging a unit or a platform pack
that has just been used or a pack that has been in direct sunlight or other hot area for a while, let the pack cool
down before you recharge it.
9.
Both the lamp and the charging platform will heat up while charging, but especially during the last 20 or 30
minutes of the charge. Both will cool down when the green light comes on.
10. Remove the battery pack from the platform when the
safe when mounted on the platform, but charging stops when the green light comes on.
11. Be sure to unplug the lamp or the charging platform from the power source when you've finished charging.
When you charge a new battery pack or a pack that has not been used for a long period of time, it may not accept a full
charge. This is normal and does not indicate a problem. Fully discharge the battery pack and then recharge it a couple of
NOTE THAT THIS UNIT MUST ONLY USE A 12Vdc FLUORESCENT UV BI-PIN BULB.
CARE AND USE
Please read and follow these instructions carefully.
ALWAYS WEAR UV SAFETY GLASSES
CAUTIONS
+
-
) and negative (
) contact pins that stick out of the base of the lamp handle or the
CHARGING
times, and this will correct the condition.
be obtained by calling 800-233-2155
green
light indicates that the unit is not
green
light comes on. The battery pack is completely
Replacement bulb may

Advertisement

loading

Summary of Contents for Bayco UVR-9014

  • Page 1 • CHARGING Only use the Bayco battery pack bases and charging platforms. Plug the charger platform into the power source using the proper cord: 120V AC wall plug or the 12V DC auto adapter plug. Only charge the pack between 50ºF and 105ºF.
  • Page 2 Do not try to penetrate the pack or work on the batteries. Only use the Bayco lamp or recharging platform. Only use the 2A output wall power supply; DO NOT use any other Bayco power supply or try to use a lower output power supply.

This manual is also suitable for:

017398290005