Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Oldfield Treco 63
- Page 1 6’ 8’ 10’ GARDEN SHEDS 63, 65, 67, 69, 83, 85, 87, 89, 103, 105, 107 & 109 TRECO SHEDS ARE MANUFACTURED TO COMPLY WITH ALL AUSTRALIAN STANDARDS Please visit the manuals section at our website for any updates or corrections to this manual www.oldfields.com.au/treco/index.htm - 11/06...
- Page 2 INSTALLATION ADVICE When you first unpack your shed, construction may look complicated ... but it really isn’t. Simply follow the illustrated instructions and your Garden Shed will be erected quickly and accurately. THIS MANUAL WILL BE USED FOR THE FOLLOWING GARDEN SHED MODEL NUMBERS APPROX.
- Page 3 TOOLS REQUIRED Note: All the tools listed are required for the erection of the garden shed. These tools should be at hand before starting work. 1. Step ladder 2. Spanner 3. Tape measure 4. Cordless power screw driver or power drill 5.
- Page 4 IMPORTANT INSTRUCTIONS STEP A - FOUNDATION A solid foundation is required. Construct a level concrete slab, reinforced with 5mm diameter x 200mm grid wire mesh. Allow 7 days minimum curing time before erecting your shed. You may select other methods of constructing a solid base using paving slabs or timber if desired, but please ensure it is level and provides secure anchorage.
- Page 5 PARTS LIST PART Corner panel Half Corner panel Door Brace Door Fascia Door Jamb Door panel Entry/Exit Ramp Front Base Zed Front Mid-Wall brace Hardware: Kit Bag Corner Gusset Door Glide Door Glide Wheel Door handle TR01031Q Door Spacer Door Track Bracket Owner’s Manual Ridge End Cap Roof Corner Cap...
- Page 6 PARTS - Pack 'A' 63, 65, 67, 69, 83, 85, 87, 89, 103, 105, 107 & 109 Refer to parts listing for 6', 8' & 10' model shed labels, sizes and quantities. Corner Panel Wall Panel Corner Panel 63, 65, 67 &...
- Page 7 PARTS - Pack 'B' 63, 65, 67, 69, 83, 85, 87, 89, 103, 105, 107 & 109 Refer to parts listing for 6', 8' & 10' model shed labels, sizes and quantities. Front Base Rail Side Top Rail Front/Rear Top Rail Side Base Rail Rear Mid-Wall Brace Roof Beam...
- Page 8 FOUNDATIONS 100mm Add 100mm to roof size depth Door Add 100mm to roof size width 100mm C A L E N D A R 7 14 21 28 1 8 15 22 29 2 9 16 23 30 3 10 17 24 4 11 18 25 Add 7 days 5 12 19 26...
- Page 9 PRE-ASSEMBLE FRONT AND BACK GABLES, ROOF BEAMS AND FRONT BASE RAIL - BEFORE ERECTING SHED. Front Gable X6 + X9 Door Glide INSIDE OF SHED Outside of shed 'I' has holes for wall panel Note: Do not fix 'X12' to end holes X13B 'I' has no holes facing inside of shed...
- Page 10 STEP 1 - Continued Back Gable Screw Gables to top rail as shown for front gable. Note: There is no X26 brackets for back gable assembly. Tighten with 2 x 'X13A + X13B' for all 10' shed models. X13B Only tighten with 1 x 'X13A + X13B' for all 6'and 8' shed models X13A...
- Page 11 STEP 1 - Continued Note: X15A Gable Brackets for 10' Wide Shed only X13B Roof Beam Quantity of part 'P' = 2 for 6' and 8' shed models. Join 2 x 'P' to create centre roof beam. Quantity of part 'P' = 4 for 10' shed models. Join 2 x 'P' for centre roof beam Note: Leave Leave 2 x 'P' = 'P singles' for left and right roof beams.
- Page 12 STEP 2 BASE FRAME ASSEMBLY Front Base Rail Side Base Rails Back Base Rail Corner Gussets...
- Page 13 STEP 3 INSTALLING CORNER PANELS, MID & TOP WALL BRACES AND WALL PANELS Corner Panels Corners 'F' and half corners 'F6' supplied with 45° degree bend. With a supporter, bend the panels 90° degrees manually. (Do not over bend). Supporter Supporter Use 'F6' (front half corner panel) Use 'F' for all 8' and 10' shed models.
- Page 14 STEP 3 - Continued H = Top Rail Mid-Wall Brace Fix top rail 'H' and mid-wall rail Curved side of H rail 'HA' to front corner 'F'(or 'F6') for roof fixing, flat side Top-Wall Brace to stabilise front corner before for wall fixing fitting back corners.
- Page 15 STEP 3 - Continued Lift mid & top wall (braces) 'H' & 'HA' into position and fix corner panel 'F' to 'H' & 'HA' rails with 2 x 'X12'. F or F6 Wall Panels Fix wall sheet 'K' to the side of shed overlapping the back corner sheet.
- Page 16 STEP 4 INSTALLING ROOF GABLES, FRONT & BACK MID-WALL RAILS & DOOR JAMBS Gables Back Mid-Wall Rail Corner Gussets 1. Fix with 'X12's the front and back gables to the corner panels 'F'. Fix with 'X12's through the top rail 'H' and gable for each corner.
- Page 17 STEP 4 - Continued Back Wall Panels Front Mid-Wall Rails Door Jambs 4. Continue to fix remaining wall sheets 'K' to back of shed. 5. Fix door jambs 'L' under the front corner panel 'F' and fix with screws to the front top rail 'I' and base rail 'C' (repeat for both door sides).
- Page 18 STEP 5 INSTALLING CENTRE ROOF BEAM - ALL MODELS Centre Roof Beam Fix pre-assembled centre roof beam 'P' to top of back and front gables and secure with 2 x 'X13A + X13B' for each gable. Back X13B Gable X13A REPEAT FOR FRONT GABLE...
- Page 19 STEP 5.1 FOR 10' SHED MODELS ONLY INSTALLING LEFT AND RIGHT ROOF BEAMS Left & Right Roof Beam Quantity of part 'P' = 4 for 10' shed models only. Use 2 x remaining 'P singles' for left and right roof beams. Follow diagrams as shown.
- Page 20 STEP 6 INSTALLING ROOF END PANELS, ROOF PANELS, ROOF CAPPING AND TRIMS Roof End Caps Panel to Panel All fasteners on roof need washers 'X11' attached. X13A Fix roof ends 'RQ' with bolts & washers from top of appex to the side wall, as shown in diagram. Fix screws &...
- Page 21 STEP 6 - Continued Roof Panels Roof Capping 1.Starting at the back fix all roof panels 'S' to one side of shed, overlapping parts 'RQ'. 2.After completion of one side fix back roof panels 'S' on other side. Fixing 'U3' and 'U2' capping as you progress. 3.Note: 'U3' capping are to be placed on front and rear of roof.
- Page 22 STEP 6 - Continued X13A Roof Trims X13A X13B 'X10' X13B Fix roof end cap to front and back on top roof capping. Fix roof edge trim 'T' to side of roof with corner caps 'X8' to each corner. STEP 7 DYNA-BOLTING BASE RAILS TO CONCRETE AND SEALING FLOOR 6.5mm x 36mm Dynabolt Seal with silicone on inside of base...
- Page 23 STEP 8 FIXING DOORS AND FASCIA Doors Fascia Note: Dynabolt base rails to concrete before fitting doors. Construct doors as shown in diagram A. Fix doors to shed as shown in diagram B. OUTSIDE SHED X13B X13A TR01031Q After fixing and adjusting INSIDE SHED the doors attach the door...
- Page 24 FOR ALL TECHNICAL INFORMATION WARRANTY AND SPARE PARTS PLEASE CALL (02) 4627 0777 This material is copyright C 2006 Oldfields Pty Ltd. Apart from any use as permitted under the Copyright Act 1968, all other rights are reserved. You may download, store in cache, display, print and reproduce the material in unaltered form only (retaining this notice, or links to it where they appear) for your personal, non-commercial use.
Need help?
Do you have a question about the Treco 63 and is the answer not in the manual?
Questions and answers
Is it possible to purchase door glides for an Oldfield Treco shed? not sure of the age of the shed as was here when we moved here. The glides look identical to those in the drawing.drawing
I contacted you recently about my shed. Yes my shed is also a Treco (Victa) (Not Tresco!). Its size, measuring the Anchore Rails, seems to be 2,9300 X 2,5600 mm. It is much like this one showing on the manual although it's about 30 years old. I think I can re use most of the parts, but I need a new kit to hang the doors (all broken as well as the spacers) Please, if you think this manual has some very different instructions, let me know what it is.