Summary of Contents for Otterbine/Barebo MR16
- Page 1 16 R RGBW W Lig nstalla ation/O Operat tion M Manua a l Manual P PN: 75-0116 R Rev 02 ...
-
Page 2: Table Of Contents
Lamp Installation ......................... 4 Wireless Remote Control .................... 5 Batteries ........................ 5 Linking .......................... 6 Unlinking ........................ 6 Operation ........................ 7 WiFi iBox Controller ‐ Optional ................... 8 Installation ........................ 8 Troubleshooting ........................ 9 75-0116 MR16 RGBW Lights www.otterbine.com 1-800-AER8TER... -
Page 3: Safety Instructions
• If the power cord is damaged, it must be replaced by a special cord or assembly available from Otterbine/ Barebo, Inc. or an authorized Otterbine/Barebo, Inc. sales and service center. • Avant d'entrer, pataugeant dans ou en nageant dans l'eau dans laquelle Aérateurs Otterbine ou fontaines sont installées, assurez-vous qu'ils sont physiquement déconnectés de leur source d'alimentation électrique. -
Page 4: Lamp Installation
IMPORTANT: Always replace the sealing O‐ring when changing the lamp. (O‐ring is included with Otterbine lamp replacement kits) Lamp Replacemet Kit PN: 09‐0030‐060 (MR16 RGBW Lamp w/O‐ring) A. Physically disconnect the power from the unit and the light set. Allow the lights to cool to avoid skin burns. B. Remove the light fixture(s) from the float and from the water. Dry excess water off of the light fixture. C. Remove the light ring from the housing by twisting it counter‐clockwise and lifting it off. D. Remove the glass lens and O‐ring. E. Remove the lamp by pulling it straight out of the socket. F. Push the lamp pins straight into the socket to avoid damage. Note: The socket will be damaged if the lamp is not installed properly, be certain the lamp pins are in straight alignment with the socket when removing and replacing the lamp. G. Reinstall the glass lens and a new O‐ring onto the top of the housing. Place the light ring on top of the housing so it rests in the tabs and twist it clockwise until it snaps into place. Note: If the light ring is on the housing properly, there will be approximately a 1/8” gap to the right of each tab on the housing when looking from the top. If this gap is not present, the light ring is not on properly and needs to be twisted further clockwise. H. Reinstall the light fixture(s) to the float. Reconnect power to the unit and the light set. 75-0116 MR16 RGBW Lights www.otterbine.com 1-800-AER8TER... -
Page 5: Wireless Remote Control
Otterbine Barebo Inc. Wireless Remote Control The lamps may be controlled by the wireless remote control. The wireless remote control operates at 2.4GHz and is capable of controlling lamps in up to four (4) zones. It has a maximum range of 30m (98ft). Batteries The wireless remote control uses two (2) AAA batteries. Batteries can be replaced by removing the rear cover of the remote control. There is a small slot located on the lower side of the remote. Use a fingernail, screwdriver, or other tool to begin to pry the cover off. Slowly work your way around the cover until it comes off. Slot Replace batteries observing the correct polarity. Replace cover by snapping the cover back on the unit. 75-0116 MR16 RGBW Lights www.otterbine.com 1-800-AER8TER... -
Page 6: Linking
Otterbine Barebo Inc. Linking In order for the remote to control the lamps, the lamps need to be linked to the remote. The remote control can control lamps assigned to four (4) zones. When a remote is supplied with a set of lamps, the lamps will be linked to zone 1. Follow the instructions below to link the lamps to a remote: A. Turn power off to the lamps. B. Turn power on to the lamps C. Within three (3) seconds of turning on the lamps, press the desired zone on button three (3) times. Zone On Buttons D. If successful, the lamps will blink three (3) times and then be steady on. Unlinking Follow the below instructions to unlink the lamp from the remote. A. Turn power off to the lamps. B. Turn power on to the lamps C. Within three (3) seconds of turning on the lamps, press the desired zone on button five (5) times. Zone On Buttons D. If successful, the lamps will blink ten (10) times and then be steady on. 75-0116 MR16 RGBW Lights www.otterbine.com 1-800-AER8TER... -
Page 7: Operation
Button operation is described below: A. Master On – Will turn on all lamps linked to this remote. B. Master Off – Will turn off all lamps linked to this remote. Holding the master off button will set all linked lamps to night light mode. C. Color ring – Touch the area of the ring corresponding to the desired color to change the color of the lamps for the active zone. D. Indicator – Indicates that a button on the remote is being pressed. If the indicator light is blinking fast, it indicates that the remote batteries need to be replaced. E. Color Temperature – This area of the remote will change the lighting color of the active lamps to white and set the desired color temperature. Touching toward the right will select higher color temperatures and touching to the left will select lower color temperatures. F. Saturation Control – This control will adjust the amount of white light added to the selected color of the active lamps. The higher up the control, the more white light will be added. G. Brightness Dimming – This control adjusts the brightness of the selected colors for the active lamps. The higher up the control, the brighter the lights. H. Mode – This control will initiate one of the preprogrammed sequencing modes on the active lamps. Speed + – This control will speed up the preprogrammed sequencing mode if it is currently running on the active lamps. Speed ‐ – This control will slow down the preprogrammed sequencing mode if it is currently running on the active lamps. K. Zone On – Turns on the lamps linked to zone 1 and makes zone 1 lamps active for the remote. L. Zone Off – Turns off the lamps linked to zone 1. Holding the zone off button will set all zone 1 lamps to night light mode. 75-0116 MR16 RGBW Lights www.otterbine.com 1-800-AER8TER... -
Page 8: Wifi Ibox Controller - Optional
Otterbine Barebo Inc. WiFi iBox Controller ‐ Optional The WiFi iBox controller allows the MR16 RGBW lamps to be controlled via smartphone app. The iBox provides a bridge between a WiFi wireless network and the RF control for the lamps. The iBox has a range of 30m (98ft) and must be located within 30m (98ft) of the lamps to be controlled. WiFi range is dependent on the device being used to connect to the iBox. Typical rule of thumb for the range of 2.4GHz WiFi is 46m (150ft) indoors and 92m(300ft) outdoors. Installation The Mi‐Light application will need to be installed on the device that will be used to control the lamps. The application can be found by searching for Milight in the apple store, searching for Milight from the Google Play store, or by scanning the code found in the instructions that come with the WiFi iBox controller. The iBox controller is supplied with a cable and 5V USB power supply. Plug the power supply into an appropriate outlet and connect the cable from the power supply to the iBox controller. When the iBox controller is powered up, the sys light will blink. When purchased with a set of lamps, the iBox controller will be shipped already linked to the supplied lamps and set for the controlling device to connect wirelessly directly to the iBox controller. The lamps will be linked to zone 2 of the iBox controller. For other configurations, please refer to the instructions provided by the manufacturer of the software. 75-0116 MR16 RGBW Lights www.otterbine.com 1-800-AER8TER... -
Page 9: Troubleshooting
A. Lamps don’t turn on a. Verify that the lamps have power. i. The standard lighting transformer has a photo eye and only powers the lights when it is dark. ii. If the lamps are on a timer verify that the timer is sending power to the lamps. b. The lamps themselves have to be turned on in order for them to turn on with the power supply. Try turning on the lamps with the remote or smart phone. If the lamps are on a timer or photo cell, do not turn off the lamps with the remote or smart phone app. c. Lamps are not linked to the remote / iBox controller. Relink the lamps. d. Remote is set to the wrong zone. Try using the master on button. B. Remote indicator light is stuck on a. Remove and replace batteries C. Remote indicator light flashing a. Batteries are low – Remove and replace batteries. D. Lamps are on, but remote control doesn’t control the lamps. a. Incorrect zone selected. Try operating the lamps with each zone active. b. Remote is out of range of lamps. Try operating from a closer location, or from a different angle. c. Lamps are lot linked to the remote. Relink the lamps. d. Lamps are submerged. Water will block radio waves. Make sure the lamps are above the surface of the water. 75-0116 MR16 RGBW Lights www.otterbine.com 1-800-AER8TER... - Page 10 OTTERBINE product, including but not limited to retail Purchaser's cost, loss of profits, goodwill, damages due to loss of product or interruption of service, or personal injuries to Purchaser or any person. 75-0116 MR16 RGBW Lights www.otterbine.com 1-800-AER8TER...
- Page 11 Otterbine Barebo Inc. Water Works With Otterbine! Otterbine/Barebo, Inc. 3840 Main Rd. East Emmaus, PA. 18049 U.S.A. TOLL FREE: 1-800-AER8TER (237-8837) PHONE: 610-965-6018 FAX: 610-965-6050 E-mail: aeration@otterbine.com www.otterbine.com 75-0116 MR16 RGBW Lights www.otterbine.com 1-800-AER8TER...