Related Manuals for Remco LP-BK01
Summary of Contents for Remco LP-BK01
- Page 1 LP-BK01 Lube Pump Base Kit General Information Motorcoach and Towed Vehicle Wiring Instructions INSTALLER: GIVE THESE INSTRUCTIONS TO THE END USER AFTER INSTALLATION FOR THEIR FUTURE REFERENCE.
-
Page 2: Table Of Contents
Table of Contents Limited Warranty pg 3-4 Warranty Registration pg 5-6 Overview pg 7 Towed Vehicle Electrical Wiring pg 8 Electrical Schematic (Towed Vehicle) pg 10 Installation of Taillight Diverters pg 12 Installation of Conductor Cable pg 14 Motor Home Electrical Installation pg 15 Installation of Electrical Monitor pg 15... -
Page 3: Limited Warranty
This transmission warranty is for 10,000 miles or 1 year, whichever comes first. This transmission warranty ceases under any condition when the vehicle’s mileage exceeds 40,000 miles. c. This warranty is valid only on those vehicles that have been approved by REMCO in writing for the installation of the LUBE PUMP. - Page 4 REMCO arising under the warranty or under any applicable statute or law is hereby limited to the duration of the warranty set forth above, commencing from the date of purchase.
-
Page 5: Warranty Registration
BY SIGNING THIS REGISTRATION THE UNDERSIGNED ACKNOWLEDGES THAT THE WARRANTY TERMS, CONDITIONS AND LIMITATION SET OUT IN THE REMCO LIMITED WARRANTY ATTACHED HERETO AND ON PAGES 3 AND 4 OF THE REMCO GENERAL INFORMATION MANUAL ARE PART OF THE AGREEMENT BETWEEN THE PARTIES AND INCORPORATED HERIN BY REFERENCE. - Page 6 Name: _________________________ place stamp here Address: _________________________ City, St Zip: _________________________ Remco Industries 4605 County Road 82 SE Alexandria, MN 56308 WARRANTEE REGISTRATION -------------------------------------------------------fold here-------------------------------------------------- --------------------------------------------------------fold here-------------------------------------------------...
-
Page 7: Overview
Transmission dependent. Please make sure your vehicle is equipped with a Transmission that has been approved by REMCO for use with the Lube Pump. REMCO provides the pump system, tail light system and all electrical connections. REMCO can provide the tow bar and brackets for most vehicles. -
Page 8: Towed Vehicle Electrical Wiring
INSTALLATION! CALL REMCO IMMEDIATELY! TOWED VEHICLE ELECTRICAL WIRING: The REMCO LUBE PUMP KIT includes all wiring and electrical hardware needed to connect the electronic monitor on the motor home dash panel and the LUBE PUMP in the towed vehicle. The kit provides for the automatic control of the taillights and turn signals of the towed vehicle. - Page 9 The following wiring parts are to be installed in the Motorhome. MOTOR COACH PARTS Part # Description Quantity 10010005 Motorhome Harness w/6-conductor socket & bracket 10010016 Electrical Monitor 11010030 LP-Generic Hardware Pack The following wiring parts are to be installed in the towed vehicle Part# Description Quantity...
- Page 11 TOWED VEHICLE ELECTRICAL INSTALLATION: Note 1: Towed Vehicle Electrical Installation should be conducted after installer has properly plumbed Remco Lube Pump and other Transmission related components (i.e. Port Fitting, Drain Plug, and Selector Valve). Valve with Pressure Switch on it must be properly plumbed before electrical connections can be made.
-
Page 12: Installation Of Taillight Diverters
***Note***In some installations a Selector Valve will not be used, but another valve known as a Pressure Switch assembly will be used instead and will be working in conjunction with a check valve. If your Transmission requires the use of one of these assemblies, then connect the red and black wires to the Pressure Switch Assembly. - Page 13 NOTE 3: The amber turn signals are not used, instead, the brake lights become the turn signals and brake lights for towing only. NOTE 4: Refer to electrical schematic, page 10, for steps listed below. Step 1. Start at the driver side taillight assembly. Access the wires for the taillight assembly. Step 2.
-
Page 14: Installation Of Conductor Cable
INSTALLATION OF CONDUCTOR CABLE NOTE 1: Refer to electrical schematic, page 10 for the following steps. NOTE 2: For driver and passenger side conductor cable installation, two separate wires will be routed between the driver side and passenger side taillight assembly, either inside the trunk area or underneath the vehicle. -
Page 15: Motor Home Electrical Installation
MOTOR HOME ELECTRICAL INSTALLATION: For proper installation it is necessary for you to have available the following tools which are not provided in the kit: 12 volt DC continuity tester Small wire cutter, wire stripper, wire terminal crimper ... -
Page 16: Installation Of Harness Assembly
Cut the white wire to an appropriate length, strip the end of the wire ¼”, crimp a Step 4. seamed spade terminal onto the wire; attach the wire to a suitable ground as previously described. Cut the heavy blue wire from the monitor to a suitable length, strip the wire ¼”, Step 5. - Page 17 Step 3. Find the motor home taillight tow harness wires at the back of the motorhome underneath the bumper. Step 4. Have an assistant turn ON the taillights. Step 5. Connect the continuity tester to a ground. Probe each wire for a “HOT” wire. Have an assistant turn OFF and ON the taillight Step 6.
-
Page 18: Electrical Schematic (Motor Coach)
ELECTRICAL SCHEMATIC - MOTORHOME... -
Page 19: Testing The Installation
This completes the installation and testing of the Motor Coach Side of Lube Pump System. NOTE: WHEN INSTALLATION HAS BEEN COMPLETED, THE INSTALLER NEEDS TO RETURN THE INSTALLATION INSTRUCTION BOOKLET TO THE END CUSTOMER. ALSO, THE WARRANTY CARD INCLUDED IN THE BOOKLET NEEDS TO BE COMPLETED AND RETURNED TO REMCO INDUSTRIES. -
Page 20: Towing Checklist
TOWING CHECKLIST: Make sure the tow bar, ball coupler and safety chains are all secured. Make sure the ends of the coiled connector cable are securely plugged into the motorhome socket and the towed car socket with the weight of the cable being supported by the tow bar. -
Page 21: Troubleshooting
Continue with the socket on the front of the towed vehicle. There should be 12 – 14 volts getting to the pump. Call REMCO for more information. PROBLEM: Red light/alarm comes on and Pump is running Check transmission fluid level in towed vehicle. See vehicle manual. -
Page 22: Maintenance
If you are not able to run your lube pump using your motorcoach, asks your REMCO dealer about the Off-Season Run kit (part number 10010040) not included with the lube pump kit. The Off-Season Run Kit will allow you to use your vehicles battery to run your lube pump. -
Page 23: Three Wire Taillight System Instructions
INSTALLATION OF TAILLIGHT DIVERTERS FOR A 3-WIRE SYSTEM NOTE: This system will use 3 of the 4 diverters provided in the kit. The preferred location for the solid-state diverters is as close to the taillight assembly kit as possible. Step 1. Access the wires for the taillight assembly (usually through the trunk in a sedan and wagon). - Page 24 INSTALLATION OF CONDUCTOR CABLE FOR 3-WIRE SYSTEMS NOTE: Refer to DIAGRAM , page 25 for the steps listed below. Step 1. Route the conductor cable from the socket to the diverters. Separate the towed vehicle’s conductor cable sufficiently to attach to the diverters. Step 2.
- Page 26 Wheel Drive, Four-Wheel Drive, and All Wheel Drive vehicles while towing. REMCO’S Tail Light Wiring Kit is for easy hook up of your tail lights and turn signals for towing. REMCO’S 12 Volt (DC) RV Water System Pumps 4605 County Road 82 SE Alexandria, MN 56308 1-800-228-2481...
Need help?
Do you have a question about the LP-BK01 and is the answer not in the manual?
Questions and answers