Download Print this page

Advertisement

HALO-Booth PRO™
Assembly

Advertisement

loading
Need help?

Need help?

Do you have a question about the HALO-Booth PRO and is the answer not in the manual?

Questions and answers

Summary of Contents for Global Halotherapy Solutions HALO-Booth PRO

  • Page 1 HALO-Booth PRO™ Assembly...
  • Page 2: Table Of Contents

    Thank you for purchasing the HALO-Booth PRO™. Be sure to read this assembly Manual thoroughly before beginiing assembly. Keep instructions on händ for reference. Table of Contents Parts ................................. 2 Tools ................................ 3 Assembly ..............................4 HALO-Fx Halogenerator™ Installation ..................... 9 HALO-Booth PRO™...
  • Page 3: Parts

    2x holder 1x 6. Side panel 13. Volume rear 2x knob 1x 7. Side posts 14. Tablet 2x (one will holder X1 hold Halo- FX and has opening; one is solid) © 2017 Global Halotherapy Solutions, LLC Page 2...
  • Page 4: Tools

    A. Star tip cover 15 , and 25 B. Philips small, electrical Tools The tools you will need to assemble the HALO-Booth PRO™ 1. Level 2. Torque / Screw Gun 3. Philips Tips (sizes) 4. Star Tip (size) 5. Rubber Mallet 6.
  • Page 5: Assembly

    ‘seated’ is to place into groove at front of floor at slight angle and ‘rock’ toward post groove as demonstrated in video. Make sure that they are securely and evenly in groove. © 2017 Global Halotherapy Solutions, LLC Page 4...
  • Page 6 8. Place Roof Panel (Part #2) in place using two people and step ladder, lining up grooves with the glass. Secure with screws (part #20) as in figure below. 9. Pull cable wires on Halogenerator side through Roof Panel (Part #2) openings. See figure below. © 2017 Global Halotherapy Solutions, LLC Page 5...
  • Page 7 12. Mount upper hinge (Part # 9) directly to roof panel (Part #2). See figure below. 13. Place glass door into ‘socket’ on floor panel (Part #1) on appropriate side and screw (Part #20) in place lining up with upper hinge nest. © 2017 Global Halotherapy Solutions, LLC Page 6...
  • Page 8 16. Mount door knob (Part #10) by screwing in place in opening in door. See figure below. Check door seal for creases and tight seal. 17. Mount tablet holder on outside of door. DO NOT tighten until lined up properly. See figure below. © 2017 Global Halotherapy Solutions, LLC Page 7...
  • Page 9 Retrieve volume knob from top of roof panel (it should be taped in place). Insert in the hole marked “volume”. See figures below. 19. Mount interior scoop (part #19-F, see photo above), using knobs, onto inside posts. Scoop will lay flat after a few uses. © 2017 Global Halotherapy Solutions, LLC Page 8...
  • Page 10: Halo-Fx Halogenerator™ Installation

    25. Connect cables on roof panel (part #2) using photo in figure below and labels on wires. Feed light chain through hole in roof panel (part #2- see photo on next page). © 2017 Global Halotherapy Solutions, LLC Page 9...
  • Page 11 27. Place vent hole sleeve into hole by insulation for vent. Place vent cone (part #18) into sleeve. 28. Slide very carefully into final room placement. 29. Place chair inside HALO-Booth PRO. Plug into standard 110 V outlet. © 2017 Global Halotherapy Solutions, LLC...
  • Page 12: Halo-Booth Pro™ Operation

    2. Connect Bluetooth device by pushing button on Philips Bluetooth. Adjust Volume on Bluetooth device by turning volume knob. User can adjust volume using their connected bluetooth device. 3. Use pull string inside to turn on additional light if desired. Maintenance and Care © 2017 Global Halotherapy Solutions, LLC Page 11...