Summary of Contents for Arena Luci CO670L
- Page 1 DMX Dimmer Pack 6ch User's Manual 10A x 6 channels dimmer pack with digital DMX / analog 010V input control and preheat function CO670L...
- Page 2 CO670L WARNINGS This unit should only be used for purpose for Make sure that cables cannot cause trip hazard. which it has been intended and should be Do not attempt to dismantle and modify the unit. installed using the instructions which are Due to the high technological level of this unit, any service maintenance should be performed by provided. Arena Luci cannot be held liable for ...
-
Page 3: Before Starting
Arena Luci dealer Each output channel has a 10A magnetic circuit immediately. breaker. The unit is equipped with a thermalcontrolled fan. n° 1 dimmer pack CO670L When the temperature is over 45°C, the fan will start automatically. Before starting the installation of your product The auto tracking of frequency and phase enables make sure that there are no evident damages ... -
Page 4: Installing The Unit
CO670L REAR PANEL / TERMINAL BOARD (9) DMX IN/OUT (XLR3 pin) (10) DMX IN/OUT (RJ11, phone jack) (11) Output terminal board (12) Power input terminal board (20A each phase) 9 10 INSTALLING THE UNIT Respect the LNE polarity indicated on the terminals (color brown = L1 or L, black = L2, grey The unit must be fixed on a suitable support which remains stable during operation. Always make = L3, blue = N, yellow / green = E). It is essential that each unit is correctly earthed sure the rack or structure to which you are setting the unit is secure and is able to bear the weight of and that electrical installation conforms to all the ... -
Page 5: Connecting Control Signals
USER'S MANUAL CONNECTING CONTROL SIGNALS The dimmer pack, in order to be remotely controlled, requires a digital signal DMX 512 (1990). The connection between controller and dimmer pack and between dimmer pack and dimmer pack must be made with twocore shielded cable with a section of at least 0.5mm ... -
Page 6: Operation
CO670L Pin 4 and pin 5 are not connected. For RJ11 PROJECTOR ADDRESSES plugs: pin 1 = +12V, pin 2 = DATA+, pin 3 = DATA , pin 4 = GND. Connect the signal coming from the controller to the DMX socket of the unit labeled DMX IN. Continue connecting the DMX OUT socket to the DMX IN socket of the next unit. - Page 7 USER'S MANUAL present, the corresponding output channel will Dimming/Switch Setting Press DMX button into DMX status. take the higher value between DMX signal and slider value. Press and hold the FNC button for 3 seconds. The default setting for all channels (AL) is When the dimmer pack is receiving a DMX frame, if the signal is lost (or the cable is disconnected) dimming mode (=d). the outputs will take the value set by the sliders. Also, ...
-
Page 8: Technical Specification
CO670L TECHNICAL SPECIFICATION Power supply 90÷240 V AC 4563 Hz Output current 10A max each channel Control Standard DMX512/1990 control signal, 6 control channels Connector XLR 5pin IN/OUT (front) Connector XLR 3pin IN/OUT (rear) Connector RJ116p4c phone jack IN/OUT (front + rear) Control Analog signal DC 010V, 6 control channels Connector Dtype plug 9pin Female Channels 6 independent, phasecut dimming, 230V ac outputs Connection Terminal blocks, input and output Material Aluminium and steel plate Colour Epoxy powder paint finish, black Insulation class Weight 7 kg Dimensions 482 x 88 x 300 mm Standard rack 19" 2U Protection IP20 Ambient Temperature From 0°C to +35°C Not allowed to be fitted on normally inflammable surfaces Applied standards CO670L ENR0 | 07/2018 WARRANTY CONDITIONS 2009/125/CE reg. (UE) 1194/2012, Energy label ...
Need help?
Do you have a question about the CO670L and is the answer not in the manual?
Questions and answers