Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Dancover Manuals
  4. Lawn and Garden Equipment
  5. TITAN Arch 320
  6. Manual

Dancover TITAN Arch 320 Manual

Greenhouse
Hide thumbs

Advertisement

Quick Links

Download this manual
Manual
for
Greenhouse
TITAN Arch 320
14-05-2019

Advertisement

loading
Need help?

Need help?

Do you have a question about the TITAN Arch 320 and is the answer not in the manual?

Questions and answers

Related Manuals for Dancover TITAN Arch 320

Summary of Contents for Dancover TITAN Arch 320

  • Page 1 Manual Greenhouse TITAN Arch 320 14-05-2019...
  • Page 2 Dear clients! After making the decision of buying a greenhouse you received a carefully made item. Its framework is made from special (1mm of thickness and 78mm width) profiles produced from galvanized metal which are extremely strong. Due to uncomplicated instruction this greenhouse is easy to construct. Because of additional items, you will be able to accomplish your ideas.
  • Page 3 The list of parts TITAN Arch 320 Name Length, NO. 1 Short arch (top) 1820mm NO. 2 Side arch (left, right on top) 1200mm NO. 3 Side – bottom stilt of the arch(left, 1310mm right) NO. 4 Pillars to the ground 200mm NO.
  • Page 4 Plastic door opening handle Screw with loop Gum to seal gap between the wall and the roof DOOR NO. 1 Part of the door with 930mm hinges DOOR NO. 2 Part of the door with a 930mm handle DOOR NO. 3 Bottom/top part of the 885mm door (horizontal part)
  • Page 5 Scheme for cutting polycarbonate Correctly separate sides of the polycarbonate. Attach the side with UV protection to the outside. UV protection layer is covered with the tape with note signs, while other side (attaching to the inside) is covered with the clear sheet. YOU MUST USE GLOVES WHILE CUTTING! It is recommended to cut sheet with electric disc saw, saw or sharp knife.

  • Page 6: Installation Instruction

    Installation instruction: 1. For the construction of the foundation basis you should use: Front and back parts of the foundation basis (13), sides of the foundation basis (11). You should connect all 4 parts and make a rectangle. To make a rectangle use: angles of the foundation (14), screw the parts together with screws M5-12 (16), internal screws M5 (19) (1.1 - 1.4 fig.).
  • Page 7 3. Dig pits (25cm diameter, 40cm depth) for digging in Side – bottom stilt of the arch (NO. 3). Dig them along the perimeter of the foundation basis, near the fastening points marked on the foundation basis (3.1 - 3.2 fig.). 3.2 fig 3.1 fig 4.
  • Page 8 Vertical mounting holes 6 fig 7. To already constructed foundation basis screw arches with screws M5-12 (16) and internal screws (19) (7.1 - 7.2 fig.). Approval of the archs in the corners and in the connection place of the foundation Соllected Foundation basis arches...
  • Page 9 Foundation basis 8.1 fig For bigger than 12m arch greenhouse TITAN Arch 320, additional crossbars are used to strengthen arches (8.2 fig.). If length of the greenhouse is 6 m – fastenings to the arches – crossbars are attached: (No. 5) + (No. 6).
  • Page 10 10) 83 cm small angle (23). Wide part to the front 11) 5 cm big angle (22). Narrow part to the front 9.1 fig Small angle Big angle 9.3 fig 9.2 fig 10. Stilt of the door – window (No. 8) should be attached to foundation basis and collected arches with the screws M5-12 (16) and internal screws (19).
  • Page 11 10.1fig 10.2 fig 11. By the part (NO.8), screw Transversal stilt of the door – window 985mm (No. 10) to Stilt of the door – window. Use screws M5-12 (16) and internal screws M5 (19)(11.1 - 11.2 fig.). 11.2 fig 11.1 fig 12.
  • Page 12 13. Firstly, screw profiles for fastening 1465mm (No. 7) with screws M5-12 (16) and internal screws M5 (19)to the side arch in height of 1,96m from the foundation basis. Another part of the profile should be placed on fastening of the arch – crossbar (No. 5) and screwed with screws M5-12 (16) and internal screws M5 (19) (13.1-13.4 fig).
  • Page 13 14 fig 15. If sides of the polycarbonate are over the framework of arches, cut them along the carcass. Place gum to seal gap between the wall and the roof (28) on the top of the sheets and only then place upper part of the polycarbonate ( -10- 2100x6000mm) (15 fig).
  • Page 14 Polycarbonate attachment points 16 fig 17. Another sheet of polycarbonate (10) should be placed on top of the fitted sheet. Screw it only on attachment points same like in the step 16. Polycarbonate sheets should be equal to the side of foundation basis both in front and back.
  • Page 15 18.2 fig 19. Based on the given scheme, cut the poly- carbonate (5;6;7;8;9) Polycarbonate parts of the door window must be fitted only when the door hinges are attached to the framework of the green- house. Polycarbonate sheets of door – window are attached with screws M5-12 (16) and inter- nal screws M5 (19) and gasket slides (20) to the door frame.

  • Page 16: Contact Information

    Contact information Head office: Dancover A/S For more information Nordre Strandvej 119 G please visit: 3150 Hellebæk www.dancovershop.com Denmark National contact Denmark: 70 26 76 20 Spain: 911 436 828 denmark@dancover.com espana@dancover.com UK: 020 8099 7570 Italy: 02 479 21 198 uk@dancover.com...