Contents
dimo
Alkaline Battery
Quick guide
(AAA)
Insert the battery
STEP 1.
Insert the battery referring to the battery cap image guide.
1
2
Battery Cap Open
Insert the Battery
(With the + mark facing down)
(Turn the cap counterclockwise
and open)
Downloading NEO STUDIO App & Pen connection
STEP 3.
Download the 'NEO STUDIO' to smart devices.
1) App Downloading
TM
NEO STUDIO
The app can be downloaded from Google Play and Apple Store.
* Please search for 'NEO STUDIO'.
** Dimo is not connect to 'NEO NOTES' App.
Start to write
STEP 4.
Please follow the letters below.
If it is sent to the app, it is now ready for digital handwriting !
Neo Smartpen dimo
Digitize your handwriting
Reset
ETC.
Please reset the pen if it does not turn off, won't charge, or
stops working. To reset the pen, press and hold the power
button for 10 seconds or remove and reinsert the battery,
then the pen will be turned off and restart.
Tips for using the correct battery
• The enclosed alkaline batteries can be natural discharge.
• Batteries are consumables and should be replaced after a
certain period of time. In addition, the usage time varies
depending on the usage environment.
• Be sure to remove the battery when you will not be using
the pen for a long time. Prevents paid service due to leakage.
• Manganese battery or rechargeable battery can not guarantee
the use time.
LED Color Status Key
Status
Power on
Power off
Low battery power
App connection
Firmware update
Low storage / Firmware update failed
Sensor recognition or
(2)
Usage environment check
Dimming: Indicates slowly getting dark and then bright while flashing.
⑴
Check if there's any dirt around optical sensor or on papers.
⑵
Precautions
Be sure to remove the battery
when you will not be using the pen for a long time.
Prevents paid service due to leakage.
Please be careful not to cover
the optical sensor with your fingers.
Otherwise, your writing may not be recognized.
When a strong impact is applied to the ball pen nib,
the product may malfunction.
For more accurate handwriting recognition,
please use the recommended nibs.
(You can check the recommended pen nib
list on the Neo smartpen official website.)
In case of processing ball pen nib with tape,
it is difficult to use.
Additional
Storing pen without pen cap may cause degradation of functionality
•
due to dust and foreign substances on the optical sensor.
The pen cap should be placed on the pen if not in use and
•
if the cap gets dirty, please clean with soft cloth or cotton swab.
If you write on the edge of the page where there is no code,
•
your handwriting may not be recognized.
Please check the details and frequently asked questions
on the Neo smartpen homepage and online mall.
www.neosmartpen.com
Please visit official Neosmartpen mall to buy
compatible notebooks and accessories.
https://shop.neosmartpen.com/
Quick Guide
4
3
Battery Cap Close
(Place the mark
in a straight line,
close the cap and turn clockwise)
LED color
Illuminating
Dimming
-
-
-
-
-
⑴
Illuminating → Dimming
Illuminating
Dimming
Dimming
Illuminating
Name of Each Part
Pen nib
Pen Grip
Handwriting
recognition sensor
Power On
STEP 2.
Press the power button ; the LED light will be turned on in 1 second.
2) App Setting
Enable the 'Bluetooth and 'GPS' function of the smart device.
3) App & Pen connection
① Please allow necessary permissions after running the app.
② Follow the on-screen instructions to connect the app and
the pen and write in STEP4.
③ The pen LED lights up green when the app and pen are connected.
Power Off
STEP 5.
When the pen is on, press the power button for 2 seconds,
the LED light will start flashing and the pen will turn off.
If there is no action taken for more than 20 minutes, the pen will turn off
automatically. (You can set the auto power off time in the app. The longer
you set the time, the shorter the pen usage time.)
Holding the Pen
*The recognition rate is affected by the direction of the optical sensor's angle.
The sensor (oval shaped part adjacent to the pen tip) should face downwards.
Deviating from the appropriate degree, or holding the pen in the wrong direction
could cause difficulties with capturing your writing or drawing.
Usage Angle
Allowable Recognition Angle
Hold the pen with
Product's acceptable recognition
the ball point nib facing up
Product Specification
NWP-F30
Model Name
Polycarbonate
Pen Body Material
Bluetooth 4.2 Classic / BLE
Connectivity
2402~2480MHz
Receiving/Transmitting Frequency
RF Output Power
3mW / Class 2
Type of emission
F1D
Battery
Alkaline battery(AAA/R03) 1ea
Nonstop writing : 9.5 Hr
Runtime
Memory
2MB of internal memory
(Saves up to about 3 sheets of A4 size)
Ink refills
D1 pen ink refills
Function
Real time-transfer mode
Usage Environment
Temperature for storage(No operation) : -10 ~ 50℃
Relative humidity : ~90%
Operation temperature : 10~35℃
140 mm / 14.7mm / 26.5g
Length / Diameter / Weight
FCC Information to User
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Caution
Modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IMPORTANT NOTE : FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
NOTE : THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)
THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
IC Information to User
This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interfer-ence, including interference that may cause
undesired operation of the device Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
PRODUCT WARRANTY
Please contact the store where you purchased the product or
NeoLAB Convergence for customer service/support.
Product Warranty
Product Name
Product No. (Serial No.)
Purchase Date
Seller
Purchase Price
· Keep the product no. (serial no.) in a safe place as it is required for checking the product warranty
period when requesting customer service / support.
· The product no. is attached on the surface of the product package.
LED(color status display)
Battery cap
Power button
Battery cap binding guide
Pen cap
Pen clip
click!
angle is -30º ~ +40º
(90º vertical standard)
Need help?
Do you have a question about the dimo and is the answer not in the manual?
Questions and answers