Mood Light; Radio; Setting The Display Brightness; Activating/Deactivating Bluetooth - Beurer WL 50 Instructions For Use Manual

7.5 Mood light

The wake up light can also be used as a mood light. The
mood light comes in the following colours:
White (3 brightness levels) -> Yellow -> Blue -> Green
-> Red -> Mood light with change of colour -> Off
1. To switch on the mood light on the wake up light, brief-
ly tap the sensor surface (speaker surface on the top
of the device).
2. To switch between the different mood lights, tap the
sensor surface (speaker surface on the top of the de-
vice) again.
3. To switch the mood light off again, press the sensor
surface (speaker surface on the top of the device) for
longer (approx. 2 seconds).

7.6 Radio

The device has max. 30 memory spaces for radio stations.
1. To switch on the radio, press the Mode button twice.
The current radio frequency will appear on the display.
2. To begin or stop the automatic station search, press
the button. Any stations found are automati-
OK
cally saved.
3. To switch between the individual stored stations, briefly
press the or
4. To set the volume, press and hold the
button.
5. To switch the radio off, press the Mode button until the
time appears on the display.
Note
To improve reception, insert the AUX cable into the
AUX connection on the rear of the device. The AUX
cable functions as an antenna.

7.7 Setting the display brightness

The device has three display brightness levels.
• To set the display brightness, press the Display button.
100% -> 50% -> display off

7.8 Activating/deactivating Bluetooth

To play your own music on the wake up light via Blue-
tooth , you must first activate Bluetooth
®
Bluetooth on the wake up light, proceed as follows:
®
1. Press the Mode button. BLUE appears in the display,
and starts to flash.
2. The wake up light can now be connected with other
devices (e.g. smartphone) via Bluetooth
vice is connected to the wake up light via Bluetooth
an acoustic signal will sound on the wake up light,
and the Bluetooth symbol
®
button.
or the
®
. To activate
®
. Once a de-
®
will light up. If Blue-
tooth has been disconnected, the acoustic signal on
®
the wake up light will sound again and the Bluetooth
symbol goes out.
3. To deactivate Bluetooth
the Mode button until the time appears in the dis-
play. The Bluetooth
4. To switch between individual songs stored on the con-
nected device on the wake up light, briefly press the
or
5. To set the volume on the wake up light, press and hold
the or the
6. Press the Mode button to exit Bluetooth

7.9 AUX connection

You can connect an external audio source (e.g. MP3 play-
er, smartphone or CD player) to the wake up light via the
AUX input.
1. Connect the supplied AUX cable to an audio source
(e.g. smartphone).
2. Insert the other end of the AUX cable into the AUX input
on the rear of the wake up light.
3. Press the Mode button three times.
display. The external audio source is now connected
to the wake up light.
4. The music settings can only be adjusted on the paired
device, not on the wake up light itself. It is also possible
to adjust the volume on the wake up light.
5. Press the Mode button to exit AUX mode again.

7.10 Switching off the wake up light

Note
All saved data is lost when the wake up light is switched
off.
• To switch off the wake up light, slide the
on the rear of the device to the "Off" position.

8. Cleaning and storage

• Clean the device with a dry cloth.
• Do not use any abrasive cleaning products.
• Ensure that no water enters the device. If this should
happen, only reuse the device once it has fully dried out.
• Never immerse the device, USB mains adapter, micro
USB charging cable or AUX cable in water or other
liquids.
• Protect the device from impacts, moisture, dust, chem-
icals, marked temperature fluctuations and nearby
sources of heat (ovens, heaters).
,
®
14
on the wake up light, press
®
symbol goes out.
®
button.
button.
AUX
®
mode again.
®
appears in the
switch
On | Off