Wesco 272301 Operating Instructions And Parts Manual

Industrial Products, Inc.

Description

The Wesco Non-Sparking Drum Deheader is designed
specifically to open 30 and 55 gallon steel drums. It features
a sharp edged hardened non-ferrous alloy replaceable blade
and a comfortable plastic hand grip.
This product is distributed by:
Wesco Industrial Products, Inc
1250 Welsh Road
North Wales, PA 19454
Tel: 215-699-7031 Fax: 215-699-3836
Contact the factory for parts information and ordering.
Visit us on the web at www.wescomfg.com

Unpacking

When unpacking the Wesco Product, check carefully for
shipping damage and missing parts. If damage has occurred
or any parts are missing, file a claim with the delivering carrier
within 24 hours and notify the dealer from whom the unit was
purchased.

Warranty Repairs

If the unit does not work properly, contact your dealer or the
factory (215-699-7031) for units less than 90 days old.

Maintenance

(1) Lubricate moving parts periodically.
(2) Check bolts and nuts frequently for tightness.
(3) Refer to steps 2 & 6 under General Safety Information
3
7
8
9
5
2
10 11
Operating Instructions and Parts Manual
ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR WESCO DRUM
13
1
12
6
4
Figure 1
Non-Sparking Drum Deheader
(Part # 272301)
DEHEADER, READ THESE INSTRUCTIONS BEFORE USING.

General Safety Information

Warning: The Wesco Drum Deheaders are designed for
specific functions. To insure proper use, the following
instructions must be adhered to:
(1) The Drum Deheaders are designed for use with steel
drums only. Do not use to open any type of fiber or plastic
drums.
(2) All threaded parts must be tight except for use the
adjustment knobs. Check frequently to be sure that no
parts are loose. If any parts are loose, remove the unit
from service and repair.
(3) Non-Sparking Deheader adjustment handle should be
hand tight only.
(4) The E-Clips (P/N 170513) and Cutting Blade (P/N
*
272302) for non-sparking Drum Deheader (P/N
272301) are made from Beryllium Copper Alloy. This
material is considered hazardous by the OSHA
Hazard Communications
1910.1200).
Never grind, sharpen, drill, or machine Beryllium
copper parts. Any of these processes will generate
Beryllium Copper dust that is harmful if inhaled. Do
Not breathe this dust, it may cause cancer. Wash
hand thoroughly after handling. Buy only original
replacement E-Clips and blades from Wesco.
(5) Bronze and Brass components of this product
**
contain lead or arsenic. The state of California under
Proposition 65 has determined that exposure to these
chemicals is known to cause cancer or birth defects
or other reproductive harm. Please wash hands after
use.
(6) After using the Drum Deheader to cut a drum's lid, use
extreme care when lifting the cut lid from the drum. Avoid
rubbing your fingers or hands along the inside of the
chime where the cut was made.
(7) Use only genuine Wesco replacement parts when
servicing.
Item Part No.
1 170501
2 170502
**
3 170503
**
4 272302
*
5 170505
**
6 170506
**
7 170507
**
8 170508
**
9 170509
**
10 170510
**
11 170511
**
12 170512
13 170513
*
Standard

Replacement Parts

Description
Handle Aluminum
Rim Guide Aluminum Bronze
Body Leaded Red Brass
Cutting Blade Beryllium Copper
Link Aluminum Bronze
Link Pin Aluminum Bronze
Adjustment Handle Manganese Bronze
Adjustable Knob Aluminum Bronze
Shoulder Screw Aluminum Bronze
Lockwasher Bronze
Hex Head Screw Bronze
Handgrip Vinyl Plastic
E-Clip Beryllium Copper
(29 CFR
Material Qty
1
1
1
1
2
2
1
1
1
2
2
1
2
179013E